MPS430 REGISTER SET
The following is a list of the MPS430 registers used by AS430:
Sixteen 16-bit registers provide adddress, data, and
special functions:
pc / r0 - program counter
sp / r1 - stack pointer
sr / r2 - status register
cg1 / r2 - constant generator 1
cg2 / r3 - constant generator 2
r4 - working register r4
r5 - working register r5
...
r14 - working register r14
r15 - working register r15
MPS430 ADDRESSING MODES
The following list specifies the format for each addressing mode
supported by AS430:
Source/Destination Operand Addressing Modes
As/Ad Addressing Mode Syntax Description
----- --------------- ------ -----------
00/0 Register mode Rn Register contents are operand.
01/1 Indexed mode X(Rn) (Rn + X) points to the operand,
X is stored in the next word.
01/1 Symbolic mode ADDR (PC + X) points to the operand,
X is stored in the next word,
Indexed mode X(PC) is used.
01/1 Absolute mode &ADDR The word following the
instruction, contains the
absolute address.
10/- Indirect @Rn Rn is used as a pointer to the
register mode operand.
11/- Indirect @Rn+ Rn is used as a pointer to the
autoincrement operand. Rn is incremented
afterwards.
11/- Immediate mode #N The word following the
instruction contains the
immediate constant N. Indirect
autoincrement mode @PC+ is used.
The terms ADDR, X and N may all be expressions. Note that not
all addressing modes are valid with every instruction, refer to
the MPS430 technical data for valid modes.
MPS430 Instruction Mnemonics
The following table lists all MPS430 family mnemonics recognized
by the AS430 assembler. The designations src and dst refer to
required source and/or destination addressing mode arguments.
* ADC[.W];ADC.B dst dst + C -> dst
ADD[.W];ADD.B src,dst src + dst -> dst
ADDC[.W];ADDC.B src,dst src + dst + C -> dst
AND[.W];AND.B src,dst src .and. dst -> dst
BIC[.W];BIC.B src,dst .not.src .and. dst -> dst
BIS[.W];BIS.B src,dst src .or. dst -> dst
BIT[.W];BIT.B src,dst src .and. dst
* BR dst Branch to .......
* BRANCH dst Branch to .......
CALL dst PC+2 -> stack, dst -> PC
* CLR[.W];CLR.B dst Clear destination
* CLRC Clear carry bit
* CLRN Clear negative bit
* CLRZ Clear zero bit
CMP[.W];CMP.B src,dst dst - src
* DADC[.W];DADC.B dst dst + C -> dst (decimal)
DADD[.W];DADD.B src,dst src + dst + C -> dst (decimal)
* DEC[.W];DEC.B dst dst - 1 -> dst
* DECD[.W];DECD.B dst dst - 2 -> dst
* DINT Disable interrupt
* EINT Enable interrupt
* INC[.W];INC.B dst dst + 1 -> dst
* INCD[.W];INCD.B dst dst + 2 -> dst
* INV[.W];INV.B dst Invert destination
JC/JHS Label Jump to Label if Carry-bit is set
JEQ/JZ Label Jump to Label if Zero-bit is set
JGE Label Jump to Label if (N .XOR. V) = 0
JL Label Jump to Label if (N .XOR. V) = 1
JMP Label Jump to Label unconditionally
JN Label Jump to Label if Negative-bit is set
JNC/JLO Label Jump to Label if Carry-bit is reset
JNE/JNZ Label Jump to Label if Zero-bit is reset
MOV[.W];MOV.B src,dst src -> dst
* NOP No operation
* POP[.W];POP.B dst Item from stack, SP+2 -> SP
PUSH[.W];PUSH.B src SP - 2 -> SP, src -> @SP
RETI Return from interrupt
TOS -> SR, SP + 2 -> SP
TOS -> PC, SP + 2 -> SZP
* RET Return from subroutine
TOS -> PC, SP + 2 -> SP
* RLA[.W];RLA.B dst Rotate left arithmetically
* RLC[.W];RLC.B dst Rotate left through carry
RRA[.W];RRA.B dst MSB -> MSB . ....LSB -> C
RRC[.W];RRC.B dst C -> MSB . ......LSB -> C
* SBC[.W];SBC.B dst Subtract carry from destination
* SETC Set carry bit
* SETN Set negative bit
* SETZ Set zero bit
SUB[.W];SUB.B src,dst dst + .not.src + 1 -> dst
SUBC[.W];SUBC.B src,dst dst + .not.src + C -> dst
SBB[.W];SBB.B src,dst dst + .not.src + C -> dst
SWPB dst swap bytes
SXT dst Bit7 -> Bit8 ........ Bit15
* TST[.W];TST.B dst Test destination
XOR[.W];XOR.B src,dst src .xor. dst -> dst
Note: Asterisked Instructions
Asterisked (*) instructions are emulated.
They are replaced with coreinstructions
by the assembler.
... Exit the ASxxxx Documentation
... Home Page