TCP/IP Package for RT-11 Documentation

TCP/IP Package for RT-11 Version 2.40, 15-Jun-2008 CHAPTER 1 SOFTWARE INSTALLATION 1-1 1.1 INSTALLATION CONFIGURATIONS 1-1 1.1.1 Install All Files on System Device 1-2 1.1.2 Install Only Command Files on System Device 1-2 1.1.3 Install All Files on a Logical Disk 1-2 1.2 SOFTWARE COMPONENTS 1-2 1.3 INSTALLATION IN DETAIL 1-6 CHAPTER 2 HARDWARE INSTALLATION 2-1 2.1 Q-BUS SYSTEMS 2-1 2.2 UNIBUS SYSTEMS 2-2 2.3 SERIAL PORT INSTALLATION 2-2 CHAPTER 3 RT-11 SYSTEM GENERATION 3-1 3.1 DEVICE HANDLER SUMMARY 3-2 CHAPTER 4 CONFIGURING RT-11 FOR REMOTE LOGIN 4-1 CHAPTER 5 PROGRAM OPTIONS 5-1 5.1 TCPIP 5-1 5.2 SKTMON 5-8 5.3 PASSWORD SETUP 5-9 5.4 TELNET 5-10 5.5 RTELNT 5-11 5.6 RPTLNT 5-12 5.7 CNCT 5-14 5.8 RCNCT 5-15 5.9 RPCNCT 5-16 5.10 FTP 5-18 5.11 FTPL 5-20 5.12 RFTP 5-22 5.13 MAIL 5-24 5.14 MMAIL 5-26 5.15 RPOP3 5-28 5.16 MAILER 5-29 5.17 RSMTP 5-31 5.18 RAUTH 5-32 5.19 LLPQRM 5-34 5.19.1 LLPC 5-35 5.19.2 LLPQ 5-35 5.19.3 LLPR 5-35 5.19.4 LLPRM 5-36 5.20 RLPD 5-36 5.21 LPRINT 5-37 5.22 LPQRM 5-39 5.22.1 LPC 5-41 5.22.2 LPQ 5-41 5.22.3 LPR 5-41 5.22.4 LPRM 5-41 5.23 NTSND 5-42 5.24 RHTTP 5-42 5.25 RGOPH 5-44 5.26 PMON 5-49 5.27 UTIL 5-50 5.27.1 LCD 5-50 5.27.2 LDEL 5-51 Page ii 5.27.3 LDIR 5-51 5.27.4 LLS 5-51 5.27.5 LMKDIR 5-52 5.27.6 LPRO 5-52 5.27.7 LRENAM 5-52 5.27.8 LRMDIR 5-53 5.27.9 LUNP 5-53 5.28 LDISKS 5-53 5.29 ABRTCP 5-53 5.30 ABRTJB 5-54 CHAPTER 6 ETHERNET DEVICE HANDLERS 6-1 6.1 DEVICE HANDLER SYSTEM SUMMARY 6-3 6.2 DEVICE HANDLER FEATURE SUMMARY 6-4 6.3 ALTERNATE DEUNA DEVICE HANDLERS 6-5 6.4 PROGRAMMING 6-6 6.5 USE OF SPECIAL FUNCTIONS (.SPFUN) 6-6 6.5.1 Unit Specification (.SPFUN 200) 6-7 6.5.1.1 Allocate Unit 6-8 6.5.1.2 Deallocate Unit 6-9 6.5.2 Promiscuous Mode (.SPFUN 201) 6-10 6.5.2.1 Enable Promiscuous Mode 6-10 6.5.2.2 Disable Promiscuous Mode 6-11 6.5.3 Protocol Type (.SPFUN 202) 6-12 6.5.3.1 Enable Protocol Type 6-12 6.5.3.2 Disable Protocol Type 6-13 6.5.4 Multicast Address (.SPFUN 203) 6-14 6.5.4.1 Enable Multicast Address 6-14 6.5.4.2 Disable Multicast Address 6-15 6.5.5 Transmit Ethernet Frame (.SPFUN 204) 6-16 6.5.6 Receive Ethernet Frame (.SPFUN 205) 6-17 6.5.7 Frame Queueing (.SPFUN 206) 6-18 6.5.7.1 Enable Frame Queueing 6-19 6.5.7.2 Disable Frame Queueing 6-19 6.5.8 Get Ethernet Address (.SPFUN 207) 6-20 6.5.9 Get Ethernet Status Block (.SPFUN 210) 6-21 6.5.10 Abort Job I/O (.SPFUN 211) 6-22 6.5.11 Timeout / Reset (.SPFUN 212) 6-22 6.5.11.1 Receive Timeout / Reset 6-23 6.5.11.2 Transmit Timeout / Reset 6-23 6.6 HANDLERS FOR TSX-PLUS V6.0 THROUGH V6.2 6-24 6.6.1 Get PLAS Allocation Size (.SPFUN 300) 6-24 6.6.2 Initialize Handler (.SPFUN 301) 6-25 6.6.3 ENPLAS.SAV - Allocating the PLAS Region 6-25 CHAPTER 7 BUILDING THE TCP/IP PACKAGE 7-1 7.1 C COMPILER 7-1 7.2 TCP/IP PACKAGE 7-2 7.3 COMPILING OPTIONS 7-2 CHAPTER 8 DISTRIBUTION DISKS 8-1 Page iii APPENDIX A HIDDEN OPTIONS A-1 A.1 DISABLE PASSWORD A-1 APPENDIX B TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG B-1 B.1 VERSION 2.40 B-2 B.2 VERSION 2.39 B-4 B.3 VERSION 2.38 B-5 B.4 VERSION 2.37 B-6 B.5 VERSION 2.36 B-7 B.6 VERSION 2.35 B-7 B.7 VERSION 2.34 B-8 B.8 VERSION 2.33 B-9 B.9 VERSION 2.32 B-10 B.10 VERSION 2.31 B-12 B.11 VERSION 2.30 B-14 Page iv TCP/IP Package for RT-11, Version 2.40 Submitted by Alan R. Baldwin, Kent State University, Kent, Ohio 44242 Operating System: RT-11-XM or RT-11-ZM Source Langauge: DECUS C and RT-11 Macro Abstract: The TCP/IP Package for RT-11 provides networking services for mapped RT-11 systems. The package is an assemblage of server and client programs designed to provide Telnet, FTP, Mail, POP3, LPD, and HTTP services for local and remote users of RT-11 sys- tems. The programs are written in C and RT-11 macro. A secu- rity system allows usernames/passwords and authorizations for each client/server component to be specified for each user. The sources for the 'TCP/IP Package for RT-11' include header, command, C language, and macro files. The DECUS C com- piler (with some bug fixes) and AS assembler are included with the software distribution to allow the package to be recompiled from the supplied sources. The current implementation uses upto 16 global regions to support multiple client/server programs simultaneously. Each client program uses 1 region except for the FTP variants (FTP, FTPL, and RFTP) which use an additional region during data transfers. The network control program TCPIP uses one addi- tional region for fragmented packet reconstruction. The hardware requirements are an RT-11 mapped system (version 5.3 or later) having a minimum of 512k bytes of memory, a DECNA (Pro), a DEQNA/DELQA (Q-Bus), or a DEUNA/DELUA (Unibus) ethernet card with associated transceiver (thick, thin, or CAT-5) and op- tionally a pair of dedicated serial lines for a remote Telnet session. Alan R. Baldwin Physics Department Kent State University Kent, Ohio 44242 tel: (330) 672 2531 fax: (330) 672 2959 Internet: baldwin@kent.edu baldwin@shop-pdp.kent.edu CHAPTER 1 SOFTWARE INSTALLATION The TCP/IP Package software components should be installed as described in the following sections. The ethernet device handler specific to your particular hardware configuration must be copied to the RT-11 system device. The logical name assign- ments used by the package are: 1. TCP: Location of client/server programs and assorted configuration, message, and help files. 2. PAS: Location of password files. 3. ENx: Selected device driver units 0-3. The logical name assignments MAI:, location of mailboxes, HTP:, location of HTTP home directory, and GPH:, location of GO- PHER files, may be used in various command files. The TCP/IP Package for RT-11 executables are found on logical disks RTDSK1.DSK, RTDSK2.DSK, and RTDSK3.DSK. The required device handlers are found on the logical disks DVDSK1.DSK and DVDSK2.DSK. 1.1 INSTALLATION CONFIGURATIONS The RT-11 package may be installed in one of the following three configurations: SOFTWARE INSTALLATION PAGE 1-2 INSTALLATION CONFIGURATIONS 1.1.1 Install All Files on System Device All command files and client/server programs are copied directly to your system disk. Assign SY: to TCP:. This confi- guration puts everything in one place but installs about 90 files (and 2100 blocks) on your system disk. 1.1.2 Install Only Command Files on System Device Create a seperate logical disk (assigned as TCP:) for the client/server programs and perhaps seperate logical disks for the password files (assigned as PAS:) and mail boxes (assigned as MAI:). Copy the command files to the system directory. This will install about 50 files (and 50 blocks) on your system device. 1.1.3 Install All Files on a Logical Disk Create a seperate logical disk (assigned as TCP:) for the package and perhaps seperate logical disks for the password files (assigned as PAS:) and mail boxes (assigned as MAI:). Copy all the files to the TCP: disk. This configuration re- quires the user to specify the TCP: logical when using any TCP/IP command file or program but removes all files from the system disk. CCL commands may be defined to obviate the need for using TCP:, see the file RTUCL.INS for a complete set of de- finitions using IND command files or RTUCLV.INS for definitions using the VRUN command without command files. Edit the selected file to include only the CCL definitions you wish defined. 1.2 SOFTWARE COMPONENTS The following annotated list summarizes the software components: 1. TCP/IP Network Server 1. TCPIP.COM TCPIP startup command file 2. TCPIP.SAV TCPIP network server Program 3. TCPIP.CFG TCPIP configuration file 2. Telnet Client 1. TELNET.COM TELNET startup command file 2. TELNET.SAV TELNET client program SOFTWARE INSTALLATION PAGE 1-3 SOFTWARE COMPONENTS 3. Remote TELNET Server 1. RTELNT.CML TELNET server startup command line 2. RTELNT.COM TELNET server startup command file 3. RTELNT.SAV TELNET server program 4. RTELNT.MSG TELNET server message file 5. RTELNT.HLP TELNET server help file 4. Remote Telnet Port Server 1. RPTLNT.CML TELNET Port server startup command line 2. RPTLNT.COM TELNET Port server startup command file 3. RPTLNT.SAV TELNET Port server program 4. RPTLNT.MSG TELNET Port server message file 5. RPTLNT.HLP TELNET Port server help file 5. CNCT Client 1. CNCT.COM CNCT startup command file 2. CNCT.SAV CNCT client program 6. Remote CNCT Server 1. RCNCT.CML CNCT server startup command line 2. RCNCT.COM CNCT server startup command file 3. RCNCT.SAV CNCT server program 4. RCNCT.MSG CNCT server message file 5. RCNCT.HLP CNCT server help file 7. Remote CNCT Port Server 1. RPCNCT.CML CNCT Port server startup command line 2. RPCNCT.COM CNCT Port server startup command file 3. RPCNCT.SAV CNCT Port server program 4. RPCNCT.MSG CNCT Port server message file 5. RPCNCT.HLP CNCT Port server help file 8. FTP Client 1. FTP.COM FTP startup command file 2. FTP.SAV FTP client program 3. FTPCMD.TXT FTP command help text 9. FTPL Client 1. FTPL.COM FTPL startup command file 2. FTPL.SAV FTPL client program SOFTWARE INSTALLATION PAGE 1-4 SOFTWARE COMPONENTS 10. Remote FTP Server 1. RFTP.CML FTP server startup command line 2. RFTP.COM FTP server startup command file 3. RFTP.SAV FTP server program 4. RFTP.MSG FTP server message file 5. RFTP.HLP FTP server help file 11. MAIL Client 1. MAIL.COM MAIL startup command file 2. MAIL.SAV MAIL client program 3. MAICMD.TXT MAIL command help text 12. MMAIL Client 1. MMAIL.COM MMAIL startup command file 2. MMAIL.SAV MMAIL client program 3. MMACMD.TXT MMAIL command help text 13. POP3 Mail Server 1. RPOP3.CML RPOP3 server startup command line 2. RPOP3.COM RPOP3 server startup command file 3. RPOP3.SAV RPOP3 server program 14. MAILER Task 1. MAILER.CML MAILER task startup command line 2. MAILER.COM MAILER task startup command file 3. MAILER.SAV MAILER task program 15. Remote MAIL Server 1. RSMTP.CML MAIL server startup command line 2. RSMTP.COM MAIL server startup command file 3. RSMTP.SAV MAIL server program 4. RSMTP.HLP MAIL server help file 16. Local Printer Utilities 1. LLPC.COM LLPC local start printer queue 2. LLPQ.COM LLPQ local printer queue status 3. LLPR.COM LLPR local print command 4. LLPRM.COM LLPRM local remove print job 5. LLPQRM.SAV LLPxx local printer control program 17. Remote LPD Server 1. RLPD.CML RLPD server startup commnad line 2. RLDP.COM RLPD server startup command file 3. RLPD.SAV RLPD server program SOFTWARE INSTALLATION PAGE 1-5 SOFTWARE COMPONENTS 18. Printer Daemon 1. LPRINT.CML LPRINT task startup command line 2. LPRINT.COM LPRINT task startup command file 3. LPRINT.SAV LPRINT task program 4. LPDQRM.CFG LPRINT configuration file 19. Remote Printer Utilities 1. LPC.COM LPC local start printer queue 2. LPQ.COM LPQ local printer queue status 3. LPR.COM LPR local print command 4. LPRM.COM LPRM local remove print job 5. LPQRM.SAV LPxx local printer control program 20. Remote Binary File Printing 1. NTSND.COM NTSND client startup command file 2. NTSND.SAV NTSND client program 21. Remote HTTP Web Server 1. RHTTP.CML RHTTP server startup command line 2. RHTTP.COM RHTTP server startup command file 3. RHTTP.SAV RHTTP server program 22. Remote Gopher Server 1. RGOPH.CML RGOPH server startup commnad line 2. RGOPH.COM RGOPH server startup command file 3. RGOPH.SAV RGOPH server program 4. RGOPH.CFG RGOPH server configuration list 23. Remote Authorization Server 1. RAUTH.CML RAUTH server startup command line 2. RAUTH.COM RAUTH server startup command file 3. RAUTH.SAV RAUTH server program 24. Port Monitor Program 1. PMON.COM PMON startup command file 2. PMON.SAV PMON program 25. Password and Authorization Files 1. PASWRD.COM Password startup command file 2. PASWRD.SAV Password program 3. PASWRD.FIL Password and authorization data file 26. Client/Server Monitor SOFTWARE INSTALLATION PAGE 1-6 SOFTWARE COMPONENTS 1. SKTMON.COM Monitor startup command file 2. SKTMON.SAV Monitor program 27. Subdirectory Utilities 1. LCD.COM Change directory command file 2. LDEL.COM Delete file command file 3. LDIR.COM List directory command file 4. LLS.COM List directory command file 5. LMKDIR.COM Make directory command file 6. LPRO.COM Protect file command file 7. LRENAM.COM Rename file command file 8. LRMDIR.COM Delete Subdirectory command file 9. LUNP.COM Unprotect file command file 10. UTIL.SAV Utilities program 28. Subdirectory Summary Utility 1. LDISKS.COM Subdirectory summary command file 2. RFTHLP.COM Generate RFTP.HLP command file 3. LDISKS.SAV Subdirectory summary program file 29. Miscellaneous Files 1. ABRTCP.SAV Abort all Client/Server programs 2. ABRTJB.COM Abort Client/Server Job command file 3. ABRTJB.SAV Abort Client/Server Job program 4. REMOVE.COM Remove all Client/Server global regions 5. DELAY2.SAV Programmed 2 Second Delay 1.3 INSTALLATION IN DETAIL Complete the hardware installation as described in the chapter titled Hardware Installation. Under RT-11 the most convenient installation is: 1. Create RTTCP.DSK[2400] as TCP:, a logical disk for the TCP/IP files 2. Create PASWRD.DSK[200] as PAS:, a logical disk for the password files 3. Optionally Create MAIL.DSK[nnn] as MAI:, a logical disk for the MAIL directory 4. Optionally Create HTTP.DSK[nnn] as HTP:, a logical disk for the HTTP home directory SOFTWARE INSTALLATION PAGE 1-7 INSTALLATION IN DETAIL 5. Optionally Create GOPHER.DSK[nnn] as GPH:, a logical disk for the GOPHER home directory NOTE The MAIL, HTTP, and GOPHER directories are needed only if you are going to use the mail, http, or gopher servers. The size of the MAI:, GPH:, and HTP: logical disks are what- ever is needed. 6. Copy the contents of the distribution disks RTDSK1, RTDSK2, and RTDSK3 to TCP:. 7. Verify that your RT-11 mapped system was sysgened to include timer support. If not, then perform a system generation or rebuild the device handlers to your re- quirements. 8. Copy and rename the appropriate device handler from the logical disk DVDSK1.DSK or DVDSK2.DSK to SY:. (See the chapter on device handlers for more information on selecting the appropriate device handler.) 9. Edit the file TCP:RTUCL.INS or TCP:RTUCLV.INS to in- clude the CCL commands you want and install these com- mands. 10. Edit the file TCP:TCPIP.RUN to mount TCP:, PAS:, [MAI:, HTP:, and GPH:], load the appropriate device handler and assign units 0-3 of the device handler to EN0-3, and start the selected programs. Copy TCP:TCPIP.RUN to SY:. 11. Add the line '$@SY:TCPIP.RUN' to your startup command file. 12. Copy PASWRD.SAV and PASWRD.FIL to PAS:. 13. Update the password file. The password file contains an anonymous account which you will need to update or delete. If you delete the anonymous account then add at least one valid account for initial testing with remote FTP enabled. 14. Edit the file TCP:TCPIP.CFG for your configuration. Your machine's name and IP address are required and the specification of a name server and gateway may be required for your network. SOFTWARE INSTALLATION PAGE 1-8 INSTALLATION IN DETAIL 15. Edit the files TCP:*.CML to contain the proper command line arguments for jobs started by SY:TCPIP.RUN. 16. Reboot your RT-11 system. Verify that the job TCPIP is running. (If the job did not start then check that SY:TCPIP.RUN has TCP: defined correctly, the confi- guration file path is correct, file TCPIP.CFG is cor- rect, and that the selected device driver was loaded. Try starting the TCPIP server from the console using the IND control file TCP:TCPIP.COM with the appropriate command line arguments and see what errors the program gives. 17. Verify that another networked computer can communicate with your machine by doing a 'ping'. Don't know what a ping is? Skip this step. (verifies that TCPIP is able to respond to data sent over the Ethernet wire) 18. Attempt to Telnet or FTP to a local computer using only the IP number of that computer. (verifies connections are possible) 19. Attempt to Telnet or FTP to a local computer using the computer's name. The computer's name and IP address must not be in the TCPIP.CFG file. (verifies that the name server entry is correct) 20. Attempt to Telnet or FTP to a machine not on your local network. If you use the machine's name then the name server must be working or the machine's name and IP number must be in the configurataion file TCP:TCPIP.CFG. (verifies that the gateway entry is correct) 21. If the RFTP job is running then attempt to FTP to your computer from some other networked machine using your machine's IP address. If your machine's name has not been added to the name server you must use the IP number. (verifies that the command line file TCP:RFTP.CML is correct and that password checking is working) Essentially your installation is now complete. You only need to update the password file to specify user/password informa- tion, access rights, and default FTP and MAIL directories. In- dividual program configuration information is contained in the chapter titled Program Options. CHAPTER 2 HARDWARE INSTALLATION 2.1 Q-BUS SYSTEMS A Q-Bus based RT-11 system requires the installation of a DEQNA or DELQA communications controller. A system memory of at least 512k is required when installing the Internet Package. The DEQNA/DELQA EQ22XM.SYS handler requires 36k bytes for code and packet buffers (the NQXV56.SYS handler requires 14K bytes for code and packet buffers) and the network server program TCPIP.SAV will use 64k bytes for a maximum of approximately 100k bytes before activating any client/server programs. Each active client/server program will use an additional 64k bytes plus one or two global PLAS regions each 8k bytes in size. NOTE It is possible to install the TCP/IP Package on a 248K machine using the DEQNA/DELQA 18-bit EQ18XM.SYS handler. This handler requires 7.5k bytes for code and packet buffers. This configuration allows at most one networking application to be active. Blockmode memory is recommended for use with the DEQNA/DELQA communications controller although not necessary. The DEQNA or DELQA interface is connected via a bulkhead cable assembly (with perhaps an extension ETHERNET transceiver cable) to a tran- sceiver (with either a thick, thin, or CAT-5 wire connection). HARDWARE INSTALLATION PAGE 2-2 UNIBUS SYSTEMS 2.2 UNIBUS SYSTEMS A Unibus based RT-11 system requires the installation of a DEUNA or DELUA communications controller. A system memory of at least 384k is recommended when installing the Internet Package. The DEUNA/DELUA 22-bit (Unibus Mapping) NUXV56.SYS handler re- quires 14k bytes for code and packet buffers and the network server program TCPIP.SAV will use 64k bytes for a maximum of approximately 78k bytes before activating any client/server pro- grams. Each active client/server program will use an additional 64k bytes plus one or two global PLAS regions each 8k bytes in size. NOTE It is possible to install the TCP/IP Package on a 248K machine using the DEUNA/DELUA 18-bit (Non Unibus Map- ping) EU18XM.SYS handler. This handler requires 7.5k bytes for code and packet buffers. This configuration allows at most one networking application to be ac- tive. The DEUNA or DELUA interface is connected via a bulkhead ca- ble assembly (with perhaps an extension ETHERNET transceiver ca- ble) to a transceiver (with either a thick, thin, or CAT-5 wire connection). 2.3 SERIAL PORT INSTALLATION If the system is to be configured for remote Telnet login then a pair of dedicated serial lines is required for the ses- sion. The dedicated pair consists of a multi-terminal line cross connected to second multi-terminal line via a NULL-MODEM cable. For a DLV11-J four port serial board the cross connection may be easily obtained by constructing a 4" cable with the 10 wire flat cable flipped between the two ends (1->10, 2->9, .... 10->1). Then cut wires 1,2,9,and 10 at both connectors leaving a 6-wire NULL-MODEM cable. The DLV11-J baud rate should be lim- ited to 4800 as two serial ports are required for the session and is a relatively heavy burden even for a LSI-11/73. Cross connected DZ ports will provide faster and more effi- cient communication. CHAPTER 3 RT-11 SYSTEM GENERATION The TCP/IP Package for RT-11 is for versions 5.3 and later and requires a mapped monitor of the type XM (or ZM). Device handlers supporting the DEQNA/DELQA (EQ and NQ), DEUNA/DELUA (EU and NU), and DECNA (NC) are provided for the various devices and processor configurations. The selection of the appropriate device handler is dependent upon the RT11 version and processor configuration. A custom device handler may be built using the supplied conditional files. Options for building the EQ and EU device handlers in- clude the number of internal packet buffers, device timeout, in- terrupt processing at FORK level, mfps/mtps or PSW processor types, and optional spfun selection. RT-11 SYSTEM GENERATION Page 3-2 3.1 DEVICE HANDLER SUMMARY Timer support is required for all TCP/IP Package programs and must be included when building RT11 monitors. Internal device timeout is no longer used by any device handler, however because RT11 monitors require specific device handler options the pre-built device handlers summarized in the following two tables include handlers with device timeout, sys extension, and without device timeout, nys extension. Summary of EQ/EU/NC/NQ/NU --- device drivers and supported systems: RT-11 VERSION [5.3] [5.4] [5.5] [5.6 ...] ----- ----- ----- --------- eq18xm.[ext] XM XM XM XM/ZM eq22xm.[ext] XM XM XM XM/ZM eu18xm.[ext] XM XM XM XM/ZM ncxv56.[ext] - ? ? XM/ZM nqxv56.[ext] - ? ? XM/ZM nuxv56.[ext] - ? ? XM/ZM ______.[ext] ext == sys, for monitor with device timeout ext == nys, for monitor without device timeout Summary of EQ/EU/NC/NQ/NU --- device driver features: SPFUNS DEVICE 206 207 210 211 212 EIS PSW UMR --- --- --- --- --- --- --- --- eq18xm.[ext] X X X - X X X - eq22xm.[ext] X X X - X X X - eu18xm.[ext] X X X - X X X - ncxv56.[ext] X X X - X X X - nqxv56.[ext] X X X - X X X - nuxv56.[ext] X X X - X X X X ______.[ext] ext == sys, for monitor with device timeout ext == nys, for monitor without device timeout CHAPTER 4 CONFIGURING RT-11 FOR REMOTE LOGIN The server programs RTELNT.SAV and RCNCT.SAV can be used to login to an RT-11 system: (1) The system must be sysgened for multiterminal support (3 local DL/DZ/DH lines are required) (2) Assuming the console is on line 0, cross connect lines 1 and 2 (at the same baud rate ...) (3) At boot up define the logical directories and startup the TCPIP.SAV server and RTELNT.SAV The RTELNT.CML command line file should be something like: -rctpyz 2 1 PAS:paswrd.fil 15 600 or -r -c 2 -t 1 -p PAS:paswrd.fil -y 15 -z 600 Terms: -r at connection termination, restart -c 2 RTELNT.SAV connects to line 2 -t 1 Console will connect to line 1 -p PAS:paswrd.fil -y 15 15 second login timeout -z 600 600 second inactivity timeout (4) Use the keyboard set command to change the console terminal: set TT: consol=1 Be sure you have tested the password file (by configuring first for incoming FTP service). Once the console is set you cannot change it back to your local terminal from your local terminal. CONFIGURING RT-11 FOR REMOTE LOGIN Page 4-2 When you log into RT through the TELNET link you are at the console! If you terminate the running TCPIP or RTELNT jobs while you are logged in, your connection will terminate and the RT system must be rebooted (the consol is connected to line 1 going to line 2 going nowhere). If you change the console connection while logged in then you will not get any response from the RT system (although the TCP/IP connection will still be active). You must terminate the TELNET connection from your connection terminal. (However that is accomplished from the remote sys- tem.) If you are connected from another RT system running the TCPIP package, then use CTRL-A X and request connection termina- tion. CHAPTER 5 PROGRAM OPTIONS The various client/server/utility program startup options are outlined and typical startup command files listed. 5.1 TCPIP The network server program TCPIP.SAV provides the software interface between the Ethernet device handler and the client/server programs in the TCP/IP Package. The network server program handles the processing of various network packets and services (TCP, IP, UDP, BOOTP, ARP, RARP, and DOMAIN name lookup). The TCPIP.SAV program may be started interactively (usually for diagnostic purposes) with the following options: TCPIP [?] [-f filespec] ? List this Help Text and Exit TCPIP f filespec Configuration File TCPIP uses four logical EN units for network access: three are used to receive IP(EN0:), ARP(EN1:), and RARP(EN2:) packets and one is used to transmit(EN3:) all packet types. The startup command file TCPIP.RUN loads and assigns the network server device EN to one of the network handlers: NC for the DECNA, NQ/EQ for the DEQNA/DELQA, or NU/EU for the DEUNA/DELUA, mounts and assigns the logical disk directories, and starts the selected network jobs. PROGRAM OPTIONS PAGE 5-2 TCPIP The TCPIP.RUN command file: ! TCPIP.RUN ! ! load eq: ! assign eq0: en0: ! assign eq1: en1: ! assign eq2: en2: ! assign eq3: en3: ! ! load eu: ! assign eu0: en0: ! assign eu1: en1: ! assign eu2: en2: ! assign eu3: en3: ! ! load nc: ! assign nc0: en0: ! assign nc1: en1: ! assign nc2: en2: ! assign nc3: en3: ! ! load nq: ! assign nq0: en0: ! assign nq1: en1: ! assign nq2: en2: ! assign nq3: en3: ! load nu: assign nu0: en0: assign nu1: en1: assign nu2: en2: assign nu3: en3: ! load ld: mount ld7: dl1:rttcp.dsk mount ld6: dl1:paswrd.dsk ! mount ld5: dl1:mail.dsk ! mount ld4: dl1:http.dsk ! mount ld3: dl1:gopher.dsk assign ld7: TCP: assign ld6: PAS: ! assign ld5: MAI: ! assign ld4: HTP: ! assign ld3: GPH: ! ! Select System Jobs ! assign ld7: DK: srun sy:vbgexe.sav/name:tcpip run delay2 srun sy:vbgexe.sav/name:rftp PROGRAM OPTIONS PAGE 5-3 TCPIP run delay2 ! srun sy:vbgexe.sav/name:rtelnt ! run delay2 ! srun sy:vbgexe.sav/name:rptlnt ! run delay2 ! srun sy:vbgexe.sav/name:rcnct ! run delay2 ! srun sy:vbgexe.sav/name:rpcnct ! run delay2 ! srun sy:vbgexe.sav/name:rsmtp ! run delay2 ! srun sy:vbgexe.sav/name:rpop3 ! run delay2 ! srun sy:vbgexe.sav/name:mailer ! run delay2 ! srun sy:vbgexe.sav/name:rpop3 ! run delay2 ! srun sy:vbgexe.sav/name:rauth ! run delay2 ! srun sy:vbgexe.sav/name:rgoph ! run delay2 ! srun sy:vbgexe.sav/name:rlpd ! run delay2 ! srun sy:vbgexe.sav/name:lprint ! run delay2 ! ! Finish Up ! assign sy: dk: set kmon ind The TCPIP program is usually started at RT-11 startup by insert- ing the line '$@TCPIP.RUN' in the startup command file. The network IND control files require that the command 'SET KMON IND' be included in the startup command file. The network server programs (RFTP, RTELNT, ...) when started as a foreground or system job gets the command line arguments from an associated .CML file in TCP:. For example, the RFTP.SAV program command line file RFTP.CML is: -r -p PAS:paswrd.fil -y 15 -z 600 The TCPIP.SAV program requires the configuration file TCPIP.CFG which defines all the parameters required to configure the network server. Note that TCP/IP services and tasks are commented out as these must be explicitly started under RT-11. Typical configuration parameters are detailed in the following configuration file: PROGRAM OPTIONS PAGE 5-4 TCPIP # # Example host file for TCP/IP server # # This file is free form # Separators are any char <32, 'space' and '=' # Comments are preceeded by # # # The form is keyword=value for each parameter. # The first set of parameters refer to the whole program's defaults. # These parameter values can be in any order. # Following this are the individual machine specs. # If the first machine is name "default", then it contains default # values for the rest of the machines. # # These options are specified for this host machine: # # myname=____.____.____ # my internet name # myip=___.___.___.___ # host machines's IP number # =BOOTP # to use BOOTP to get host info # =RARP # to use RARP to get IP number # netmask=___.___.___.___ # subnetting mask # domain=____.____ # default domain for lookup # nndomto=____ # timeout for domain lookups # nnretry=____ # number of retries for lookup # nnarpto=____ # timeout for ARPs # nndto=____ # timeout for data layer # nnpkt=____ # TCPIP upper limit packets per transq # # nnpkt=1, requires ACK for each packet # nnwin=____ # TCPIP upper limit window size # nnseg=____ # TCPIP upper limit input segment size # nnmtu=____ # TCPIP upper limit output transfer size # service=___,___,_____ # TCPIP services specification # task=___,___,_____ # TCPIP task specification # logsession=__________ # TCPIP session logging filespec # PROGRAM OPTIONS PAGE 5-5 TCPIP # # These are the options which may be specified for each # individual machine specification: # # name=____ # name of session (required) # host=____ # full name of host computer # hostip=___.___.___.___ # IP number of host # port=____ # specify initial connection port # nameserver=____ # name server level # gateway=____ # gateway level # retrans=____ # initial retransmit timeout # contime=____ # opening connection timeout # mwin=____ # advertized window size for this host # mseg=____ # maximum advertized input segment size # mtu=____ # maximum output transfer size # delete=backspace # value to use for character deletion # crmap=4.3BSDCRNUL # for 4.3BSD null CR # duplex=half # for half duplex TELNET connections # copyfrom=____ # copy parameters from this name # myname=machine.domain.name myip=192.3.2.100 # required, this machine's IP number netmask=255.255.255.0 # subnetting mask domain="domain.name" # domain name search path # affects machines on your local network nnwin=2920 # limit advertized window (nnwin == mwin) nndomto=5 # domain timeout nnretry=4 # number of retries nnarpto=2 # arp timeout in seconds nnpkt=2 # send only 2 packet(s) per transq PROGRAM OPTIONS PAGE 5-6 TCPIP # The following line specifies the TCPIP logging file # which will contain information for each session # started: TELNET / RTELNT / RPTLNT / CNCT / RCNCT / RPCNCT # FTP / FTPL / RFTP # MAIL / RSMTP / RPOP3 / MAILER / MMAIL # RHTTP / RGOPH / RAUTH # RLPD / LPRINT / LPQRM / LLPQRM # NTSND / PMON # logsession=sy:tcpip.log[100] # The following are services supported by TCPIP. # Each entry contains the listen port, maximum number of # sessions and the name of the command file to initiate # the service. # service=21,2,TCP:rftp.srv # remote ftp server # service=23,2,TCP:rtelnt.srv # remote telnet server # service=25,2,TCP:rsmtp.srv # remote smtp server (task: -t 1) # service=27,2,TCP:rcnct.srv # remote cnct server # service=70,2,TCP:rgoph.srv # remote gopher server # service=80,4,TCP:rhttp.srv # remote http server # service=110,2,TCP:rpop3.srv # remote pop3 server (task: -t 1) # service=113,1,TCP:rauth.srv # remote auth server # service=515,2,TCP:rlpd.srv # remote lpd server (task: -t 2) # The following specify the tasks that may be initiated by TCPIP. # Each entry contains the taskid number, timer interval in seconds # (zero means not an automatically started task), and the name # of the command file to initiate the service. These tasks donot # have to be related to TCPIP programs, however a TCPIP program # can use the TASKCLASS to start a specific task. The selected # task will be scheduled by TCPIP and only one (1) copy of the # the task will be allowed to run. Additional requests to start # the task will be queued as a single request to rerun the task # at the completion of the currently executing task. # task=1,0,TCP:mailer.srv # mail/mmail/pop3/rsmtp mail delivery agent # task=2,0,TCP:lprint.srv # rlpd/llpqrm printing delivery agent PROGRAM OPTIONS PAGE 5-7 TCPIP # # Following are individual machine specifications # Gateways are used in the order that they appear in the file # Nameservers rotate, #1, #2, #3, #1, #2 when a request fails # # The machine named "default" contains the fields which are # automatically filled in for later hosts # name=default # Session name, "default" is a reserved name # Not a real machine, default parameters only delete=delete # Assume mostly non-UNIX connections # The following entries affect the tuning of # TCP connections to this host. # They should be set by the network administrator who is familiar # with the requirements of your specific network. contime=12 # timeout in seconds to try connection # before returning error to user retrans=5 # starting retransmit time out in seconds mtu=1460 # maximum transmit unit in bytes # outgoing packet size, MAX=1460 mseg=1460 # largest segment we can receive # whatever the hardware can take, MAX=1460 mwin=2920 # most bytes we can receive without ACK # =TCP window size, MAX=3047 # larger isn't always better # # Below this line, most of the communication parameters are obtained # from the "default" host entry. # Machine names, IP addresses, and special communication parameters # are present when needed. # name=mygateway hostip=192.3.2.2 gateway=1 name=nameserver hostip=192.3.2.1 nameserver=1 name=alpha host=alpha.domain.name hostip=192.3.2.200 PROGRAM OPTIONS PAGE 5-8 TCPIP # # If during TCPIP startup you get the error Sreadhosts() error 2, # you probably have exceeded the memory limits of the machine. # # (1) reduce the number of machine definitions above # (2) or donot use session logging # # Sesion logging and Debugging should not be simultaneously enabled. # The network server needs to know the ip address(number) of the machine to which it is connecting. If the TCPIP.CFG file does not contain the named machines' ip number then it will make a request to the specified name server to obtain the machines ip number. If a name server is not specified then the connection cannot be made using the machines name (place the machines name and ip address in the configuration file). If the ip address is given as the input to the client program rather than the name then a domain name lookup is not required. All changes to the configuration file will take effect at the next startup of TCPIP.SAV. 5.2 SKTMON The SKTMON program provides a diagnostic tool for observing the state of all TCPIP connections. SKTMON displays the current state of network connections by showing the global regions through which the TCPIP network server program and the client/server programs communicate. The program shows in detail the various network packets, the incoming and outgoing data streams, and the status of the network ethernet driver. The IND control file SKTMON.COM starts the program: .sets cmdlin "0 "+"'p1'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:sktmon.sav .data 'cmdlin' .close $@sy:tcpfun PROGRAM OPTIONS PAGE 5-9 PASSWORD SETUP 5.3 PASSWORD SETUP A password file (eg PASWRD.FIL) must be built if the lo- cal/remote MAIL services are to be used or if remote network ac- cess (ie remote FTP, TELNET or CNCT) must be restricted. It is suggested that a seperate password directory be created to hold the files PASWRD.SAV and PASWRD.FIL. This directory need be no larger than about 200 blocks. The maximum number of user/pass- word specifications is limited by the program memory size to about 50. The PASWRD.FIL contains 1 block for each user/pass- word specification. The PASWRD.COM command file should be up- dated to reflect the location of the password files. A seperate directory allows the exclusion of its access by remote FTP ses- sions. Copy the file PASWRD.SAV (and optionally the supplied pass- word file PASWRD.FIL) to the created directory. Modify the PASWRD.COM file to access this subdirectory. Initiating PASWRD.SAV with a file specification will open an existing file or create the file if no existing file is found. The PASWRD program screens will indicate all the options and the file USRBLK.H illustrates the formats for the device/file speci- fications required by the password program. NOTE The password for any added user must also be speci- fied, any user not requiring a password (ie an 'anonymous' account) must have this password entered as a null string by typing only a carriage return for the password. To use the created password file be sure the program startup command files have specified the correct path to the password file. NOTE The device/file access rights are only used by the remote FTP server. PROGRAM OPTIONS PAGE 5-10 PASSWORD SETUP The IND control file PASWRD.COM starts the program: .sets cmdlin "'p1'"+"PAS:paswrd.fil" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:paswrd.sav .data 'cmdlin' .close $@sy:tcpfun 5.4 TELNET The TELNET program allows the user to initiate a connection to a remote host for a terminal session. The startup options for TELNET are: TELNET destination [?] [-hp] ? List the Help Text and Exit TELNET h List the Help Text and Open Connection p filespec Specify the Password Filespec The destination host specification may be the host name or host ip number. If the connection is to be made to an alternate port then follow the name/ip with the port number (decimal). The TELNET program supports the following command line op- tions which are activated by the META character 'control A': M->C open capture file M->D close capture file M->F FTP [internet address] M->H this help screen M->I type my internet address M->K erase character M->O abort output M->Q are you there? M->R toggle follow character M->S skip to end of buffer M->T toggle backspace/delete M->U erase line M->X close connection M->Y interrupt process M->@ send a true null character ^? abort Telnet session The IND control file TELNET.COM starts the program: PROGRAM OPTIONS PAGE 5-11 TELNET .sets cmdlin "-hb "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:telnet.sav .data 'cmdlin' .close $@sy:tcpfun 5.5 RTELNT RTELNT is a server program for a remote TELNET session into RT-11. The program startup options are: RTELNT [?] [-hmp filespec] [-ceqrtvyz] [parameters] ? List the Help Text and Exit RTELNT c i Connection Line i is attached to Terminal Line j e Enable Monitoring of all Transactions h Specify the Help Filespec m Specify the Message Filespec p Specify the Password Filespec q n Specify an Alternate Connection Port r Restart RTELNT after Disconnect t j Terminal Line j is attached to Connection Line i v Verbose Mode y s Login Timeout in seconds z s Inactivity Timeout in seconds The program may be started interactively (for diagnostic pur- poses) by the command file RTELNT.COM: .sets cmdlin "-rpyz PAS:paswrd.fil 15 600 ... ... "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rtelnt.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RTELNT.CML: -r -p PAS:paswrd.fil -y 15 -z 600 The RTELNT help and message files are RTELNT.HLP and RTELNT.MSG PROGRAM OPTIONS PAGE 5-12 RTELNT respectively. The h or m options may be used if these files are not on the TCP: device. These files are created by the system manager and are not required. 5.6 RPTLNT RPTLNT is a server program that provides a mechanism to con- nect the 'CONSOLE' port of a LSI/PDP computer system to the net- work. The program runs on an independent networked computer which provides the service connection to the 'CONSOLE' port of an at- tached computer system through a network TELNET connection. The program supports the generation of a 'BREAK' which en- ables the user to enter ODT on most LSI and some PDP machines. The default 'break' key is ^E. The program startup options are: RPTLNT [?] [-hmp filespec] [-cekqrtvyz] [parameters] ? List the Help Text and Exit RPTLNT c i Connection Line number e Enable Monitoring of all Transactions h Specify the Help Filespec k c Break Character m Specify the Message Filespec p Specify the Password Filespec q n Specify the Connection Port r Restart RPTLNT after Disconnect t j Terminal line parameters v Verbose Mode y s Login Timeout in seconds z s Inactivity Timeout in seconds PROGRAM OPTIONS PAGE 5-13 RPTLNT The terminal line parameters are defined as follows: code - (O+P+L+SSSS) - (OPLxSSSS) SSSS - baud rate code (decimal) + 0 50 + 1 75 + 2 110 + 3 134.5 + 4 150 + 5 300 + 6 600 + 7 1200 + 8 1800 + 9 2000 +10 2400 +11 3600 +12 4800 +13 7200 +14 9600 +15 19200 note: not all controllers support all baud rate values, check device documentation. L - + 0 for 7-Bit - + 32 for 8-Bit P - + 0 for no parity - + 64 for parity O - + 0 even parity (when P = 1) - +128 odd parity (when P = 1) The program may be started interactively (for diagnostic pur- poses) by the command file RPTLNT.COM: .sets cmdlin "-rbctqmyz 1 14 1173 ... ... TCP:rptlnt.msg 15 600 "+"'p1' 'p2'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rptlnt.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file PROGRAM OPTIONS PAGE 5-14 RPTLNT TCP:RPTLNT.CML: -rbctqmyz 1 14 1173 TCP:rptlnt.msg 15 600 The RPTLNT help and message files are RPTLNT.HLP and RPTLNT.MSG respectively. The h or m options may be used if these files are not on the TCP: device. These files are created by the system manager and are not required. 5.7 CNCT The CNCT program allows the user to initiate a connection to a remote RT-11/TSX-Plus host for a terminal session. This pro- gram is the TELNET program stripped of all TELNET negotiations and uses a non standard TCP port (27). The startup options for CNCT are: CNCT destination [?] [-hp] ? List the Help Text and Exit CNCT h List the Help Text and Open Connection p filespec Specify the Password Filespec The destination host specification may be the host name or host ip number. If the connection is to be made to an alternate port then follow the name/ip with the port number (decimal). The CNCT program supports the following command line options which are activated by the META character 'control A': M->C open capture file M->D close capture file M->F FTP [internet address] M->H this help screen M->I type my internet address M->O abort output M->Q are you there? M->S skip to end of buffer M->X close connection M->Y interrupt process ^? abort CNCT session The IND control file CNCT.COM starts the program: PROGRAM OPTIONS PAGE 5-15 CNCT .sets cmdlin "-hb "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:cnct.sav .data 'cmdlin' .close $@sy:tcpfun 5.8 RCNCT RCNCT is a server program for remote CNCT sessions into RT-11. This program is the RTELNT program stripped of all TELNET negotiations and uses a non standard TCP port (27). The startup options for RCNCT are: RCNCT [?] [-hmp filespec] [-ceqrtvyz] [parameters] ? List the Help Text and Exit RCNCT c i Connection Line i is attached to Terminal Line j e Enable Monitoring of all Transactions h Specify the Help Filespec m Specify the Message Filespec p Specify the Password Filespec q n Specify an Alternate Connection Port r Restart RCNCT after Disconnect t j Terminal Line j is attached to Connection Line i v Verbose Mode y s Login Timeout in seconds z s Inactivity Timeout in seconds The program may be started interactively (for diagnostic pur- poses) by the IND control file RCNCT.COM: .sets cmdlin "-rpyz PAS:paswrd.fil 15 600 ... ... "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rcnct.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RCNCT.CML: -r -p PAS:paswrd.fil -y 15 -z 600 PROGRAM OPTIONS PAGE 5-16 RCNCT The RCNCT help and message files are RCNCT.HLP and RCNCT.MSG respectively. The h or m options may be used if these files are not on the TCP: device. These files are created by the system manager and are not required. 5.9 RPCNCT RPCNCT is a server program that provides a mechanism to con- nect the 'CONSOLE' port of a LSI/PDP computer system to the net- work. The program runs on an independent networked computer which provides the service connection to the 'CONSOLE' port of an at- tached computer system through a network CNCT connection. The program supports the generation of a 'BREAK' which en- ables the user to enter ODT on most LSI and some PDP machines. The default 'break' key is ^E. The program startup options are: RPCNCT [?] [-hmp filespec] [-cekqrtvyz] [parameters] ? List the Help Text and Exit RPCNCT c i Connection Line number e Enable Monitoring of all Transactions h Specify the Help Filespec k c Break Character m Specify the Message Filespec p Specify the Password Filespec q n Specify the Connection Port r Restart RPCNCT after Disconnect t j Terminal line parameters v Verbose Mode y s Login Timeout in seconds z s Inactivity Timeout in seconds PROGRAM OPTIONS PAGE 5-17 RPCNCT The terminal line parameters are defined as follows: code - (O+P+L+SSSS) - (OPLxSSSS) SSSS - baud rate code (decimal) + 0 50 + 1 75 + 2 110 + 3 134.5 + 4 150 + 5 300 + 6 600 + 7 1200 + 8 1800 + 9 2000 +10 2400 +11 3600 +12 4800 +13 7200 +14 9600 +15 19200 note: not all controllers support all baud rate values, check device documentation. L - + 0 for 7-Bit - + 32 for 8-Bit P - + 0 for no parity - + 64 for parity O - + 0 even parity (when P = 1) - +128 odd parity (when P = 1) The program may be started interactively (for diagnostic pur- poses) by the command file RPCNCT.COM: .sets cmdlin "-rbctqmyz 1 14 1173 ... ... TCP:rpcnct.msg 15 600 "+"'p1' 'p2'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rpcnct.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file PROGRAM OPTIONS PAGE 5-18 RPCNCT TCP:RPCNCT.CML: -rbctqmyz 1 14 1173 TCP:rpcnct.msg 15 600 The RPCNCT help and message files are RPCNCT.HLP and RPCNCT.MSG respectively. The h or m options may be used if these files are not on the TCP: device. These files are created by the system manager and are not required. 5.10 FTP The FTP program provides reliable data transfer between cooperating computer systems. The FTP program startup options are: FTP [?] [-f filespec] [-p filespec] [-ghinrv] [destination host] ? List this Help Text and Exit FTP f filespec Command File g Wildcard Expansion Disabled h FTP Help List i Interactive Prompting Off n AutoLogin Disabled on Connect p filespec Specify the Password Filespec r Output Redirection Disabled v Verbose Mode Disabled The destination host specification may be the host name or host ip number. If the connection is to be made to an alternate port then follow the name/ip with the port number (decimal). If the work file device, wf:, is not assigned then the pro- gram will fail to execute the commands mget, mdel, or mls. The IND control file FTP.COM starts the program: .sets cmdlin "-hb "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:ftp.sav .data 'cmdlin' .close $@sy:tcpfun The FTP program supports the following command line options: ? print local help information PROGRAM OPTIONS PAGE 5-19 FTP ascii set ascii transfer type bell toggle command completed beep bget get a file in binary mode binary set binary transfer type bput put a file in binary mode bye terminate ftp session and exit cd change remote working directory close terminate ftp session debug toggle/set debugging mode delete delete remote file - inquires if prompting is on dir list contents of remote directory duplicate enable/disable duplicate packets get receive file hash toggle printing `#' for each 1024 bytes transferred help print local help information home set default directory to home interactive turn on prompting for multiple commands lcd change local working directory ldelete delete local files ldir list contents of local directory lls list contents of local directory lprotect set protection flag on local file lpwd show local working directory lrename rename a local file ls list contents of remote directory ltype print a local file to the screen lunprotect clear protection flag on a local file mdelete delete multiple files mdir list contents of multiple remote directories mget get multiple files mkdir make directory on the remote machine mls list contents of multiple remote directories mode set file transfer mode mput send multiple files noninteractive turn off prompting on multiple commands open connect to remote ftp passive enable or disable passive transfer mode prompt toggle interactive prompting on multiple commands protect set protection flag on file put send one file pwd print working directory on remote machine quit terminate ftp session and exit quote send arbitrary ftp command recv receive file remotehelp get help from remote server rename rename remote file rm delete remote file rmdir remove directory on the remote machine send send one file PROGRAM OPTIONS PAGE 5-20 FTP sendport toggle use of PORT cmd for each data connection status show current status struct set file transfer structure system query remote system type type print a remote file to the screen unprotect clear protection flag on file user send new user information verbose toggle verbose mode version FTP-11 version displayed wild toggle wildcard expansion of local file names > redirect (m)dir or (m)ls response to a file The commands bget, get, put, and send allow explicit renaming of the files during the transfer by specifying the optional destination file name: bget/get/put/send [source name] [destination name] The commands put or send can be used to transfer a device im- age to an image file (must specify binary format): put/send dev:[-1] destination-image-file The commands bget and get can be used to restore a device from an image file (must specify binary format): bget/get source-image-file dev:[-1] 5.11 FTPL The FTPL program provides reliable data transfer between cooperating computer systems. FTPL is a stripped version of the FTP program for use on smaller systems. The FTPL program startup options are: FTPL [?] [-ghinv] [destination host] ? List this Help Text and Exit FTPL g Wildcard Expansion Disabled h FTPL Help List i Interactive Prompting Off n AutoLogin Disabled on Connect v Verbose Mode Disabled The destination host specification may be the host name or host ip number. If the connection is to be made to an alternate port PROGRAM OPTIONS PAGE 5-21 FTPL then follow the name/ip with the port number (decimal). If the work file device, wf:, is not assigned then the pro- gram will fail to execute the commands mget, mdel, or mls. The IND control file FTPL.COM starts the program: .sets cmdlin "-h "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:ftpl.sav .data 'cmdlin' .close $@sy:tcpfun The FTPL program supports the following command line options: ? print local help information ascii set ascii transfer type bell toggle command completed beep bget get a file in binary mode binary set binary transfer type bput put a file in binary mode bye terminate ftp session and exit cd change remote working directory close terminate ftp session debug toggle/set debugging mode delete delete remote file - inquires if prompting is on dir list contents of remote directory duplicate enable/disable duplicate packets get receive file hash toggle printing `#' for each 1024 bytes transferred help print local help information interactive turn on prompting for multiple commands ls list contents of remote directory mdelete delete multiple files mget get multiple files mkdir make directory on the remote machine mode set file transfer mode mput send multiple files noninteractive turn off prompting on multiple commands open connect to remote ftp passive enable or disable passive transfer mode prompt toggle interactive prompting on multiple commands put send one file pwd print working directory on remote machine quit terminate ftp session and exit quote send arbitrary ftp command PROGRAM OPTIONS PAGE 5-22 FTPL recv receive file remotehelp get help from remote server rename rename remote file rm delete remote file rmdir remove directory on the remote machine send send one file sendport toggle use of PORT cmd for each data connection status show current status struct set file transfer structure system query remote system type type print a remote file to the screen user send new user information verbose toggle verbose mode version FTP-11 version displayed wild toggle wildcard expansion of local file names The commands bget, get, put, and send allow explicit renaming of the files during the transfer by specifying the optional destination file name: bget/get/put/send [source name] [destination name] The commands put or send can be used to transfer a device im- age to an image file (must specify binary format): put/send dev:[-1] destination-image-file The commands bget or get can be used to restore a device from an image file (must specify binary format): bget/get source-image-file dev:[-1] 5.12 RFTP RFTP is a server program for remote FTP sessions into RT-11. The program startup options are: PROGRAM OPTIONS PAGE 5-23 RFTP RFTP [?] [-hmp filespec] [-efqruvwyz] [parameters] ? List the Help Text and Exit RFTP e Enable Monitoring of all RFTP Transactions f Enable file SIZE command h Specify the Help Filespec m Specify the Message Filespec p Specify the Password Filespec q n Specify an Alternate Connection Port r Restart RFTP after Disconnect u UNIX Style DIR Command v Verbose Mode w Write Duplicate Packets y s Login Timeout in seconds z s Inactivity Timeout in seconds The program may be started interactively (for diagnostic pur- poses) by the IND control file RFTP.COM: .sets cmdlin "-rpyz PAS:paswrd.fil 15 600 ... ... "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rftp.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RFTP.CML: -r -p PAS:paswrd.fil -y 15 -z 600 The RFTP help and message files are RFTP.HLP and RFTP.MSG respectively. The h or m options may be used if these files are not on the TCP: device. These files are created by the system manager and are not required. The -u option specifies that the 'LIST' command returns a UNIX style directory listing rather than the default RT-11 style directory format. This format is useful if the remote systems are PC's using one of the window oriented FTP utilities such as PROCOMM V3.0 (DataStorm Technologies). These utilities use the unix access-rights string to determine whether the entries are files or directories. The general form for the UNIX style directory is: PROGRAM OPTIONS PAGE 5-24 RFTP -rwxrwxrwx 1 system user 1536 12 Jan 96 file.ext drwxrwxrwx 1 system user 512000 01 Mar 96 subdir.dsk 5.13 MAIL The MAIL program provides local and internet mail services. This program is recommended for systems not requiring a POP3 server. The startup options for MAIL are: MAIL [?] [-fp filespec] [-i IP Address] [-z s] ? List the Help Text and Exit MAIL f filespec Command File h Help list i IP Address Intermediate Host Name / IP Address p filespec Specify the Password Filespec z s Connection Timeout in Seconds The Intermediate Host IP option provides a means of routing the internet mail through another host machine. The RT-11 MAIL pro- gram does not support retry operations if the mail cannot be delivered, using an intermediate host supporting retries will provide this feature to the RT-11 MAIL system. Permission to use a particular host as a MAIL relay should be obtained from the hosts' system manager. The option must be specified using the complete name (an IP address may also be used). A typical invocation follows: -i mail.domain.name The MAIL program is invoked from the IND control file MAIL.COM: .sets cmdlin "-hpz PAS:paswrd.fil 60 ... ... "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:mail.sav .data 'cmdlin' .close $@sy:tcpfun The MAIL program supports the following command line options: ? print local help information bye terminate the MAIL program copy copy a message to a file PROGRAM OPTIONS PAGE 5-25 MAIL debug toggle/set debugging mode delete delete a message dir list of unread mail messages exit terminate the MAIL program hash toggle printing `#' during transfers help print local help information home go to home (initial) directory index an index of received mail interactive turn on prompting on multiple commands last read most recent mail message lcd change local working directory ldelete delete local files ldir list contents of local directory listmail list of unread mail messages lls list contents of local directory lprotect set protection flag on local file lpwd show local working directory lrename rename a local file ltype print a local file to the screen lunprotect clear protection flag on a local file mail go to mail directory newmail count number of new mail messages noninteractive turn off prompting on multiple commands prompt toggle interactive prompting on multiple commands quit terminate the MAIL program read read a mail message scan scan directory for all mail messages send [filespec] initiate the sending of a message status show current status user enter a new user/password access key verbose toggle verbose mode version MAIL-11 version displayed wild toggle wildcard expansion of local file names Mail is sent to a local user if only a name is specified and to a remote machine if the user and IP address are specified. Local: username Internet: username@machine.domain.name The MAIL programs MAIL.SAV, MMAIL.SAV, MAILER.SAV, RPOP3.SAV, and RSMTP.SAV make use of the password file to restrict access to the mail system. A user may have local and/or remote MAIL access (or no access) depending on the password file parameters. Incoming mail may be directed to a users' default directory or to a specific mail directory (specified in the password PROGRAM OPTIONS PAGE 5-26 MAIL file). A typical configuration is to create a mail directory, SY:MAIL.DSK, and have mail subdirectories for each user. Thus the path SY:/MAIL/USER1/ specifies the users' unique mail direc- tory and should be specified in the password configuration. The local mail programs MAIL.SAV, MMAIL.SAV, and MAILER.SAV and the remote mail programs RSMTP.SAV and RPOP3.SAV check the password file to verify that the user has the privilege to send or re- ceive mail via the network and places any received mail in the specified mail directory. These programs will use/create a mail index file in the mail directory which is used to keep an index of all received mail. 5.14 MMAIL The MMAIL program is a front end interface to the MAILER ser- vice. This program is recommended for systems requiring a POP3 server. The startup options for MMAIL are: MMAIL [?] [-fp filespec] [-h] ? List the Help Text and Exit MMAIL f filespec Command File h Help list p filespec Specify the Password Filespec The MAILER delivery task must have been started in TCPIP.RUN. The MAILER actually sends the mail messages produced by MMAIL. The MMAIL program is invoked from the IND control file MMAIL.COM: .sets cmdlin "-hp PAS:paswrd.fil ... ... "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:mmail.sav .data 'cmdlin' .close $@sy:tcpfun The MMAIL program supports the following command line options: ? print local help information bye terminate the MMAIL program copy copy a message to a file debug toggle/set debugging mode delete delete a message dir list of unread mail messages exit terminate the SMAIL program PROGRAM OPTIONS PAGE 5-27 MMAIL help print local help information home go to home (initial) directory index an index of received mail interactive turn on prompting for multiple commands last read most recent mail message lcd change local working directory ldelete delete local files ldir list contents of local directory listmail list of unread mail messages lls list contents of local directory lprotect set protection flag on local file lpwd show local working directory lrename rename a local file ltype print a local file to the screen lunprotect clear protection flag on a local file mail go to mail directory newmail count number of new mail messages noninteractive turn off prompting for multiple commands prompt toggle interactive prompting on multiple commands quit terminate the MAIL program read read a mail message scan scan directory for all mail messages send [filespec] initiate the sending of a message status show current status user enter a new user/password access key version SMAIL-11 version displayed wild toggle wildcard expansion of local file names Mail is sent to a local user if only a name is specified and to a remote machine if the user and IP address are specified. Local: username Internet: username@machine.domain.name The MAIL programs MAIL.SAV, MMAIL.SAV, MAILER.SAV, RPOP3.SAV, and RSMTP.SAV make use of the password file to restrict access to the mail system. A user may have local and/or remote MAIL access (or no access) depending on the password file parameters. Incoming mail may be directed to a users' default directory or to a specific mail directory (specified in the password file). A typical configuration is to create a mail directory, SY:MAIL.DSK, and have mail subdirectories for each user. Thus the path SY:/MAIL/USER1/ specifies the users' unique mail direc- tory and should be specified in the password configuration. The local mail programs MAIL.SAV, MMAIL.SAV, and MAILER.SAV and the remote mail programs RSMTP.SAV and RPOP3.SAV check the password PROGRAM OPTIONS PAGE 5-28 MMAIL file to verify that the user has the privilege to send or re- ceive mail via the network and places any received mail in the specified mail directory. These programs will use/create a mail index file in the mail directory which is used to keep an index of all received mail. 5.15 RPOP3 RPOP3 is a server program for remote access to the RT-11 mail system via the extended POP3 protocol. This server supports the PC shareware packages PC Eudora and WinQVT/Net for Windows 3.x and NT in particular and others using the POP3 protocol. The program startup options are: RPOP3 [?] [-p filespec] [-eqrvyz] [parameters] ? List the Help Text and Exit RPOP3 e Enable Monitoring of RPOP3 Transactions p Specify the Password Filespec q n Specify an Alternate Connection Port r Restart RPOP3 after Disconnect v Verbose Mode y s Login Timeout in seconds z s Inactivity Timeout in seconds If an extended POP3 client is sending mail to the POP3 server then the MAILER delivery task must have been started in TCPIP.RUN. The MAILER actually sends the mail messages produced by RPOP3. The program may be started interactively (for diagnostic pur- poses) by the IND control file RPOP3.COM: .sets cmdlin -rpyz PAS:paswrd.fil 15 600 ... ... "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rpop3.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RPOP3.CML: -r -p PAS:paswrd.fil -y 15 -z 600 PROGRAM OPTIONS PAGE 5-29 RPOP3 The MAIL programs MAIL.SAV, MMAIL.SAV, MAILER.SAV, RPOP3.SAV, and RSMTP.SAV make use of the password file to restrict access to the mail system. A user may have local and/or remote MAIL access (or no access) depending on the password file parameters. Incoming mail may be directed to a users' default directory or to a specific mail directory (specified in the password file). A typical configuration is to create a mail directory, SY:MAIL.DSK, and have mail subdirectories for each user. Thus the path SY:/MAIL/USER1/ specifies the users' unique mail direc- tory and should be specified in the password configuration. The local mail programs MAIL.SAV, MMAIL.SAV, and MAILER.SAV and the remote mail programs RSMTP.SAV and RPOP3.SAV check the password file to verify that the user has the privilege to send or re- ceive mail via the network and places any received mail in the specified mail directory. These programs will use/create a mail index file in the mail directory which is used to keep an index of all received mail. 5.16 MAILER MAILER is a backend program for MMAIL and RPOP3 which provides mail delivery to local users and remote destinations. When MAILER is activated it scans all user mail directories for files with names similiar to ml____.nnn created by MMAIL or RPOP3. These files are routed to their respective destinations and then deleted. If the mail is not deliverable then the mes- sage is directed back to the sender. MAILER is also a backend program for MAIL, MMAIL, RPOP3, and RSMTP which provides mail forwarding from a local user to another local user or remote destination. When MAILER is ac- tivated it scans each user-mail-directory enabled for forwarding and sends any received mail to the forwarding address. After a successful forward the local mail file is deleted. Forwarding is enabled by specifying a forwarding address in the PASWRD pro- gram. The program startup options are: PROGRAM OPTIONS PAGE 5-30 MAILER MAILER [?] [-p filespec] [-i IP-address] [-t n] [-z s] [-ev] ? List the Help Text and Exit MAILER e Enable Monitoring of MAILER Transactions i IP-address Intermediate Host Name / IP Address p filespec Specify the Password Filespec t n (minutes) Continuous Scanning Time Interval v Verbose Mode z s Connection Timeout in Seconds The Intermediate Host IP option provides a means of routing the internet mail through another host machine. The RT-11 MAIL pro- gram does not support retry operations if the mail cannot be delivered, using an intermediate host supporting retries will provide this feature to the RT-11 MAIL system. Permission to use a particular host as a MAIL relay should be obtained from the hosts' system manager. The option must be specified using the complete name (an IP address may also be used). A typical invocation follows: -i mail.domain.name The program may be started interactively (for diagnostic pur- poses) by the IND control file MAILER.COM: .sets cmdlin "-pit PAS:paswrd.fil ... ... mail.domain.name 15 "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:mailer.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:MAILER.CML: -p PAS:paswrd.fil -t 15 -i mail.domain.name The specification of device wf: is required by MAILER to tem- porarily store local mail messages before writing the mail to the users mail directories. If wf: is undefined, inaccessable, or not initialized then mail will not be delivered. The MAIL programs MAIL.SAV, MMAIL.SAV, MAILER.SAV, RPOP3.SAV, and RSMTP.SAV make use of the password file to restrict access PROGRAM OPTIONS PAGE 5-31 MAILER to the mail system. A user may have local and/or remote MAIL access (or no access) depending on the password file parameters. Incoming mail may be directed to a users' default directory or to a specific mail directory (specified in the password file). A typical configuration is to create a mail directory, SY:MAIL.DSK, and have mail subdirectories for each user. Thus the path SY:/MAIL/USER1/ specifies the users' unique mail direc- tory and should be specified in the password configuration. The local mail programs MAIL.SAV, MMAIL.SAV, and MAILER.SAV and the remote mail programs RSMTP.SAV and RPOP3.SAV check the password file to verify that the user has the privilege to send or re- ceive mail via the network and places any received mail in the specified mail directory. These programs will use/create a mail index file in the mail directory which is used to keep an index of all received mail. 5.17 RSMTP RSMTP is a server program for remote MAIL into RT-11. The program startup options are: RSMTP [?] [-hp filespec] [-eiqrvz] [parameters] ? List the Help Text and Exit RSMTP e Enable Monitoring of all RSMTP Transactions h Specify the Help Filespec i i m IP Validation and Mask p Specify the Password Filespec q n Specify an Alternate Connection Port r Restart RSMTP after Disconnect v Verbose Mode z s Inactivity Timeout in Seconds The RSMTP help file RSMTP.HLP is of diagnostic use only. The program may be started interactively (for diagnostic pur- poses) by the IND control file RSMTP.COM: .sets cmdlin "-rpz PAS:paswrd.fil 600 ... ... "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rsmtp.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN PROGRAM OPTIONS PAGE 5-32 RSMTP command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RSMTP.CML: -r -p PAS:paswrd.fil -z 600 The specification of device wf: is required by RSMTP to tem- porarily store incoming mail messages before writing the mail to the users mail directories. If wf: is undefined, inaccessable, or not initialized then incoming mail will not be delivered. The MAIL programs MAIL.SAV, MMAIL.SAV, MAILER.SAV, RPOP3.SAV, and RSMTP.SAV make use of the password file to restrict access to the mail system. A user may have local and/or remote MAIL access (or no access) depending on the password file parameters. Incoming mail may be directed to a users' default directory or to a specific mail directory (specified in the password file). A typical configuration is to create a mail directory, SY:MAIL.DSK, and have mail subdirectories for each user. Thus the path SY:/MAIL/USER1/ specifies the users' unique mail direc- tory and should be specified in the password configuration. The local mail programs MAIL.SAV, MMAIL.SAV, and MAILER.SAV and the remote mail programs RSMTP.SAV and RPOP3.SAV check the password file to verify that the user has the privilege to send or re- ceive mail via the network and places any received mail in the specified mail directory. These programs will use/create a mail index file in the mail directory which is used to keep an index of all received mail. 5.18 RAUTH The program RAUTH implements the Authentication Server Pro- tocol (RFC931) which provides a means to determine whether a particular TCP connection is active. Once a connection is established, the server reads one line of data which specifies the connection of interest. If it exists, the system dependent user identifier of the connection of interest is sent out the connection. The service closes the connection after sending the user identifier. Queries are permitted only for fully specified connections. The local/foreign host pair used to fully specify the connection are taken from the query connection. This means a user on Host A may only query the server on Host B about connections between A and B. The server accepts simple text query requests of the form PROGRAM OPTIONS PAGE 5-33 RAUTH , where is the TCP port (decimal) on the target (server) system, and is the TCP port (decimal) on the source (user) system. For example: 23, 6191 The only responses supported by RAUTH are , : USERID : OTHER : system , : ERROR : NO-USER which correspond to active and not active connections repec- tively. The program startup options are: RAUTH [?] [-aenqrvyz] [parameters] ? List the Help Text and Exit RAUTH e Enable Monitoring of all RAUTH Transactions n Never authorize q n Specify an Alternate Connection Port r Restart RAUTH after Disconnect v Verbose Mode y Always authorize z s Inactivity Timeout in seconds The program may be started interactively (for diagnostic pur- poses) by the command file RAUTH.COM: .sets cmdlin "-rz 30 "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rauth.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RAUTH.CML: -rz 30 PROGRAM OPTIONS PAGE 5-34 RAUTH 5.19 LLPQRM LLPQRM is the program which submits, controls and reports the status of the local LPRINT daemon. The program performs the functions of LPC, LPQ, LPR, and LPRM. The program startup op- tions are: LLPQRM [?] [-p filespec] -o opt [opt arguments] ? List the Help Text and Exit LLPQRM p filespec LPD configuration file o lpc [?] Start printer queue lpq [?] Get printer queue status lpr [?] Submit a job to a printer queue lprm [?] Remove a job from a printer queue The -o opt argument must preceed the opt specific op- tions. The LPRINT job must be running for LLPQRM to function properly and is usually started in TCPIP.RUN. Program sub options are: LPC [?] ? List the LPC Help Text and Exit LLPQRM LPQ [?] [-#P argument] ? List the LPQ Help Text and Exit LLPQRM # n Repeat query time in seconds P Queue Name Printer Queue LPR [?] [-#IPW argument] [-flr] [file to print] ? List the LPR Help Text and Exit LLPQRM # n # of copies to print (1-5) I n Indentation P Queue Name Printer Queue (default = lp) W n Page Width f Plain Text Printing (default) l No Control Character Processing r Fortran Carriage Control Printing LPRM [?] [-P argument] [file to remove from queue] ? List the LPRM Help Text and Exit LLPQRM P Queue Name Printer Queue PROGRAM OPTIONS PAGE 5-35 LLPQRM Each of the options is invoked by an IND control file more indi- cative of its intended function. The IND control file QUOTE.COM places the arguments in quotes. DECUS C will convert everything to lower case without the quotes. 5.19.1 LLPC LLPC.COM is the local start printer daemon IND control file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:llpqrm.sav .data -pto TCP:lpdqrm.cfg 2 lpc .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' 5.19.2 LLPQ LLPQ.COM is the local check printer queue status IND control file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:llpqrm.sav .data -pto TCP:lpdqrm.cfg 2 lpq .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' 5.19.3 LLPR LLPR.COM is the local print command file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:llpqrm.sav .data -bpto TCP:lpdqrm.cfg 2 lpr .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' PROGRAM OPTIONS PAGE 5-36 LLPQRM 5.19.4 LLPRM LLPRM.COM is the local remove queued print file command file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:llpqrm.sav .data -bpto TCP:lpdqrm.cfg 2 lprm .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' For a normal user: (1) if the printer queue is not specified then all of the queues are checked. (2) If a file name is not specified then all queued files for this user are checked and the user queried for each file to be deleted. For the special user 'system': (1) if the printer queue is not specified then all of the queues are checked. (2) If a file name is not specified then all queued files for all users are checked and the 'system' queried for each file to be deleted. (3) If a username is entered, then all files for this user are checked and 'system' queried for each file deletion. (4) If a filename is entered, then the specific file is checked and 'system' queried for file deletion. 5.20 RLPD RLPD is a server program providing remote printing on the RT-11 system printer. The program startup options are: RLPD [?] [-p filespec] [-eqrv] [parameters] ? List the Help Text and Exit RLPD e Enable Monitoring of RLPD Transactions p Specify the Configuration Filespec q n Specify an Alternate Connection Port r Restart RLPD after Disconnect v Verbose Mode The LPRINT job must be running for LLPQRM to function properly and is usually started in TCPIP.RUN. The program may be started interactively (for diagnostic pur- poses) by the IND control file RLPD.COM: PROGRAM OPTIONS PAGE 5-37 RLPD .sets cmdlin "-rp TCP:lpdqrm.cfg "+"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rlpd.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RLPD.CML: -r -p TCP:lpdqrm.cfg 5.21 LPRINT The program LPRINT is the backend printing daemon servicing printing on the RT-11 system. Print jobs submitted by remote systems through the RLPD server and local print jobs submitted through LLPQRM are processed by the LPRINT task. RLPD and LLPQRM write two files (cfa.nnn and dfa.nnn) into a temporary file directory, cfa.nnn is the print control file and dfa.nnn is the print data file. At the completion of the printing job these files are deleted. The command options for LPRINT are: LPRINT [?] [-p filespec] [-t n] [-v] ? List the Help Text and Exit LPRINT p filespec Specify the Configuration Filespec t n (minutes) Continuous Scanning Time Interval v Verbose Mode The LLPQRM.CFG configuration file is of the following form: 001 ; three digit sequence sy2:\lpdtmp\ ; temporary directory sy0:\paswrd\paswrd.fil ; pass word file lp * name ls: ; line printer dspcgc * name hf: ; cgc graphics device dspqbs * name hg: ; qbs graphics device file * name sy3:\tmpwrk\ ; write to a file lp pdp * ls: ; line printer dspcgc pdp * hf: ; cgc graphics device dspqbs pdp * hg: ; qbs graphics device PROGRAM OPTIONS PAGE 5-38 LPRINT The first line is a sequence number maintained by RLPD, LLPQRM, and LPRINT. The second line is the directory used for holding the queued files until processed by LPRINT. The third line references the password file which may be used to check if the user exists. The fourth and succeeding lines contain printing queues and their access permissions. The four entries are: (1) queue name (2) machine name (* is any) (3) user name (* is any) (4) device The data is copied to the specified printing device or random access device using the name in the print control file (cfa.nnn). The program may be started interactively (for diagnostic pur- poses) by the IND control file LPRINT.COM: .sets cmdlin "-pt TCP:lpdqrm.cfg 15 " ... ... +"'p1' 'p2' 'p3' 'p4'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:lprint.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:LPRINT.CML: -p TCP:lpdqrm.cfg -t 2 The specification of device wf: is required by LPRINT to tem- porarily store data files before writing the data to subdirec- tories. If wf: is undefined, inaccessable, or not initialized then data will not be copied. PROGRAM OPTIONS PAGE 5-39 LPQRM 5.22 LPQRM LPQRM is the program which submits, controls and reports the status of remote printer queues. The program performs the func- tions of LPC, LPQ, LPR, and LPRM. The program startup options are: LPQRM [?] [-ipq argument] [-e] -o opt [opt arguments] ? List the Help Text and Exit LPQRM e Enable Monitoring of LPQRM Transactions i IP Address Remote Server Name / IP Address n Port Number Remote Server Port Number q Queue Name Remote Server Printer Queue p filespec Configuration File o lpc [?] Start printer queue lpq [?] Get printer queue status lpr [?] Submit a job to a printer queue lprm [?] Remove a job from a printer queue The -o opt argument must preceed the opt specific op- tions. Program sub options are: PROGRAM OPTIONS PAGE 5-40 LPQRM LPC [?] [-SP argument] ? List the LPC Help Text and Exit LPQRM P Queue Name Remote Host Printer Queue S IP Address Remote Host IP Address LPQ [?] [-SP# argument] [-l] ? List the LPQ Help Text and Exit LPQRM # n Repeat query time in seconds l Long form of queue status P Queue Name Remote Host Printer Queue S IP Address Remote Host Name / IP Address LPR [?] [-SPIW# argument] [-flr] [filespec] ? List the LPR Help Text and Exit LPQRM # n # of copies to print (1-5) P Queue Name Remote Host Printer Queue S IP Address Remote Host Name / IP Address f ASCII Plain Text (default) l ASCII With Controls r Fortran Carriage Control I n Indentation (f option only) W n Page Width (flr options only) Other Options: 1234cdghnoptvz UNIX(tm) Options M Mail Option C Class J Job L Banner T Title LPRM [?] [-SP argument] job [job [...]] ? List the LPRM Help Text and Exit LPQRM P Queue Name Remote Host Printer Queue S IP Address Remote Host Name / IP Address Each of the options is invoked by a command file more indicative of its intended function. The IND control file QUOTE.COM places the arguments in quotes. DECUS C will convert everything to lower case without the quotes. PROGRAM OPTIONS PAGE 5-41 LPQRM 5.22.1 LPC LPC.COM is the remote start printer daemon IND control file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:lpqrm.sav .data -po TCP:lpdqrm.cfg lpc .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' 5.22.2 LPQ LPQ.COM is the remote check printer queue status IND control file. .open tcpfun.com .data r sy:vbgexe.sav .data TCP:lpqrm.sav .data -po TCP:lpdqrm.cfg lpq .close @TCP:quote 'P1' 'P2' 'P3' 'P4' 'P5' 'P6' 5.22.3 LPR LPR.COM is the remote print IND control file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:lpqrm.sav .data -bpo TCP:lpdqrm.cfg lpr .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' 5.22.4 LPRM LPRM.COM is the remote remove queued print file IND control file. .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:lpqrm.sav .data -bpo TCP:lpdqrm.cfg lprm .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' PROGRAM OPTIONS PAGE 5-42 NTSND 5.23 NTSND NTSND is a program for transferring data to a remote printer without any translation (good for binary files). This program supports products such as the Emulex NETJET for the HP 4Si/Mx printer. The command options are: NTSND [?] [-inpq argument] file [file [...]] ? List the Help Text and Exit NTSND i IP Address Remote Server Name / IP Address n Port Number Remote Server Port Number p filespec Password File q Query for File Name The NTSND program is invoked from the IND control file NTSND.COM: .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:ntsnd.sav .data -bp PAS:paswrd.fil .close @TCP:quote 'p1' 'p2' 'p3' 'p4' 'p5' 'p6' 5.24 RHTTP RHTTP is an HTTP/0.9 server supporting only simple request and response formats for GET, HEAD, and POST methods. The POST method always responds as unimplemented. HTTP transfers are always in BINARY format except for files of type HTM, DOC, TXT, and LST which are in ASCII format. The command options are: RHTTP [?] [-p filespec] [-eqrvwz] [parameters] ? List the Help Text and Exit RHTTP e Enable Monitoring of all RHTTP Transactions p Specify the HTTP Directory and Home File q n Specify an Alternate Connection Port r Restart RHTTP after Disconnect v Verbose Mode w Write Duplicate Packets z s Inactivity Timeout in seconds The HTTP directory and home file must be specified, using the -p option. The directory path is used as the base directory for all HTTP accesses. HTTP accesses with absolute directory speci- fications (e.g. dl1:file.ext) are reported as unauthorized. The RT-11 version of RHTTP does not support subdirectory PROGRAM OPTIONS PAGE 5-43 RHTTP processing. The home file is the file read when a request is made with no file specified, this is typically the home page for this computer system. The program may be started interactively (for diagnostic pur- poses) by the IND control file RHTTP.COM: .sets cmdlin "-rpz HTP:/home.htm 30 "+ ... ... "'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rhttp.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the program gets the command line arguments from the file TCP:RHTTP.CML: -r -p HTP:/home.htm The RHTTP program requires, at the minimum, a dedicated device (logical device) and a home file. Only files in this directory are accessable by the http server. The home file is the file read by the http server when no specific file is speci- fied. The http directory and home file are specified by the RHTTP option: -p dl1:/home.htm NOTE The slash, /, is required to delimit the HTTP base directory. All accesses to files outside the http directory are not per- mitted and are reported as unauthorized. Absolute references are not allowed (e.g. dl1:/file.ext) even if they are in the http directory, these are also reported as unauthorized. Use only relative paths in file specifications to the http direc- tory. These requirements provide the most security for http re- quests which require no password authentication. PROGRAM OPTIONS PAGE 5-44 RHTTP The home file is an HTML file and should be written to re- flect the functionality of the browsers you wish to support with this http server. 5.25 RGOPH RGOPH is a simple Gopher server supporting transfers of text, binary, and image files and linking to other network resources using basic ASCII text constructs. The command options are: RGOPH [?] [-p filespec] [-aeqrvwz] [parameters] ? List the Help Text and Exit RGOPH e Enable Monitoring of all RGOPH Transactions p Specify the Master GOPHER File q n Specify an Alternate Connection Port r Restart RGOPH after Disconnect v Verbose Mode w Write Duplicate Packets z s Inactivity Timeout in seconds The Gopher master file must be specified, using the -p option. The master file contains the access specifications for the go- pher server. The format of the master file is described in the file RGOPH.CFG and included here for reference: NOTE The RT-11 version of RGOPH does not support local sub- directory processing, only real devices and logical devices are supported for local access. PROGRAM OPTIONS PAGE 5-45 RGOPH # # This is the Master Gopher List # # Each entry has the following format: #description # file or list specification # machine name or IP address # port number # # End list with '.' and # # Common item types specified by are: # # 0 item is a file # 1 item is a directory # 2 item is a CSO phone-book server # 3 Error # 4 item is a NINHEXed MacIntosh file # 5 item is DOS archive of some sort # 6 item is a UNIX uuencoded file # 7 item is an Index-Search server # 8 item points to a text-based telnet server # 9 item is a binary file # + item is a redundant server # T item points to a text-based TN3270 session # g item is a GIF format graphics file # I item is some kind of image file # # All references are described in RFC1436 # The master list contains file and list references which denote a tree structure of accessible resources. A typical master list is shown here to clarify the specification. The top level follows: PROGRAM OPTIONS PAGE 5-46 RGOPH 0 About This GOPHER Site sy2:/gopher.dsk/rgoph.doc shop-pdp.kent.edu 70 1 TCP/IP Package For TSX-Plus, ... List1/ shop-pdp.kent.edu 70 1 ASxxxx Assemblers and Linker List2/ shop-pdp.kent.edu 70 . The 'List1/' ( = 1) specification indicates this is a directory of subitems: PROGRAM OPTIONS PAGE 5-47 RGOPH # # Elements of List1/ # List1/ 0 Abstract [2K] sy3:/tcpip.pkg/abstra.doc shop-pdp.kent.edu 70 0 Documentation [158K] sy3:/tcpip.pkg/manual.doc shop-pdp.kent.edu 70 9 Minimal Package, Logical Disk Image, [300K] sy3:/tcpipm.dsk shop-pdp.kent.edu 70 9 Complete Package, Multilevel Logical ... sy3:/tcpip.pkg/tcpip.dsk shop-pdp.kent.edu 70 9 Disk1 of Package, RX02 Image [494K] sy3:/tcpip.pkg/tcpip.dsk/disk1.dsk shop-pdp.kent.edu 70 9 Disk2 of Package, RXO2 Image [494k] sy3:/tcpip.pkg/tcpip.dsk/disk2.dsk shop-pdp.kent.edu 70 9 Disk3 of Package, RXO2 Image [494k] sy3:/tcpip.pkg/tcpip.dsk/disk3.dsk shop-pdp.kent.edu 70 9 Disk4 of Package, RXO2 Image [494k] sy3:/tcpip.pkg/tcpip.dsk/disk4.dsk shop-pdp.kent.edu 70 9 Disk5 of Package, RXO2 Image [494k] sy3:/tcpip.pkg/tcpip.dsk/disk5.dsk shop-pdp.kent.edu 70 9 Disk6 of Package, RXO2 Image [494k] sy3:/tcpip.pkg/tcpip.dsk/disk6.dsk shop-pdp.kent.edu 70 9 Disk7 of Package, RXO2 Image [494k] sy3:/tcpip.pkg/tcpip.dsk/disk7.dsk shop-pdp.kent.edu 70 PROGRAM OPTIONS PAGE 5-48 RGOPH 9 Documentation Source, RX02 Image [494K] sy3:/tcpip.pkg/tcpip.dsk/tcpdoc.dsk shop-pdp.kent.edu 70 9 Current Updates, Logical Disk Image [988K] sy3:update.dsk shop-pdp.kent.edu 70 . The 'List2/' ( = 1) specification indicates the presence of a second directory of available resources: # # Elements of List2/ # List2/ 1 ASxxxx for PDP-11 and LSI-11 Computers List2.1/ shop-pdp.kent.edu 70 1 ASxxxx for PC Compatible Computers List2.2/ shop-pdp.kent.edu 70 . These elements also contain references to additional subdirec- tories of resources. Nesting to any level may be accomplished using this syntax. Ensure that all subdirectory references have unique names. The use of 'xxxxx/' is not required, any unique character string may be used to reference a subdirectory entry. The program may be started interactively (for diagnostic pur- poses) by the IND control file RGOPH.COM: .sets cmdlin "-rp GPH:/home.htm "+ ... ... "'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:rgoph.sav .data 'cmdlin' .close $@sy:tcpfun The program is normally started as a system job by the TCPIP.RUN command file. When started as a foreground or system job the PROGRAM OPTIONS PAGE 5-49 RGOPH program gets the command line arguments from the file TCP:RGOPH.CML: -r -p GPH:/home.htm 5.26 PMON PMON is a utility program which monitors a TCP port for ac- tivity. The program startup options are: PMON port [?] [-h] ? List the Help Text and Exit PMON h List the Help Text The specified port is opened for listening. When the port is opened by a remote computer all incoming data is displayed. Data entered from the keyboard is transported to the remote com- puter. The PMON program supports the following command line options, as found in the TELNET and CNCT programs, which are activated by the META character 'control A': M->C open capture file M->D close capture file M->F FTP [internet address] M->H this help screen M->I type my internet address M->K erase character M->O abort output M->Q are you there? M->R toggle follow character M->S skip to end of buffer M->T toggle backspace/delete M->U erase line M->X close connection M->Y interrupt process M->@ send a true null character ^? abort Telnet session The startup command file PMON.COM follows: .sets cmdlin "-h "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:pmon.sav .data 'cmdlin' .close $@sy:tcpfun PROGRAM OPTIONS PAGE 5-50 UTIL 5.27 UTIL The program UTIL is a compendium of various functions used to perform useful operations on RT-11 subdirectories. The command options for UTIL are: UTIL [?] [-cdlmnpqru] [filespec(s)] ? List this Help Text and Exit UTIL c change directory d delete a file l list a directory m make a directory n delete a directory p set protection flag on a file q disable query on delete r rename a file u clr protection flag on afile Each of the options is invoked by a command file more indicative of its intended function. Most of the subdirectory commands are not supported in the RT-11 version of UTIL. 5.27.1 LCD Change directory IND control file LCD.COM: .sets cmdlin "-sc 0 4 "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .data $@wf:cmdfil .close $@sy:tcpfun PROGRAM OPTIONS PAGE 5-51 UTIL 5.27.2 LDEL Delete file IND control file LDEL.COM: .sets cmdlin "-d "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun 5.27.3 LDIR List directory IND control file LDIR.COM: .sets cmdlin "-l "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun 5.27.4 LLS List directory IND control file LLS.COM: .sets cmdlin "-l "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun PROGRAM OPTIONS PAGE 5-52 UTIL 5.27.5 LMKDIR Make a subdirectory IND control file LMKDIR.COM: .sets cmdlin "-m "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun 5.27.6 LPRO Set protection flag IND control file LPRO.COM: .sets cmdlin "-p "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun 5.27.7 LRENAM Rename a file IND control file LRENAM.COM: .sets cmdlin "-r "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun PROGRAM OPTIONS PAGE 5-53 UTIL 5.27.8 LRMDIR Remove a subdirectory IND control file LRMDIR.COM: .sets cmdlin "-n "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun 5.27.9 LUNP Clear protection flag IND control file LUNP.COM: .sets cmdlin "-u "+"'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:util.sav .data 'cmdlin' .close $@sy:tcpfun 5.28 LDISKS The LDISKS program generates a subdirectory map for each device specified and optionally outputs the result to a file. This utility is not supported under RT-11. 5.29 ABRTCP ABRTCP is a program which attempts to gracefully abort the TCPIP system. All TCP/IP connections are closed, all client(s)/server(s) are requested to abort, and the TCPIP server closes. The program is invoked from the IND control file ABRTCP.COM: as: .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:abrtcp.sav .close $@sy:tcpfun PROGRAM OPTIONS PAGE 5-54 ABRTJB 5.30 ABRTJB ABRTJB is a program which attempts to gracefully abort a specific TCP/IP client/server program. The program is invoked from the IND control file ABRTJB.COM: .sets cmdlin "'p1' 'p2' 'p3' 'p4' 'p5' 'p6'" .open sy:tcpfun.com .data r sy:vbgexe.sav .data TCP:abrtjb.sav .data 'cmdlin' .close $@sy:tcpfun and may request from 1 to 6 jobs be aborted. The job aborts are sent to the TCPIP server program which closes any open connec- tions associated with the job and sends an abort request to the specified job. This program will not abort the TCPIP server program. CHAPTER 6 ETHERNET DEVICE HANDLERS The device handlers provide support for the following hardware controllers: 1. DEQNA/DELQA (EQ and NQ Drivers) 2. DEUNA/DELUA (EU and NU Drivers) 3. DECNA (NC Driver) The Ethernet handlers provide support for one controller and a maximum of 8 units numbered 0 through 7. These unit numbers are used as a logical connection between a user program and an address/protocol pair to be recognized by the Ethernet hardware. The NC/NQ/NU device handlers are the DEC handlers modified to include special functions 206 (enable/disable frame bufferring), 207 (get physical address), 210 (get handler status block), and 212 (device time-out and reset) . These handlers support only RT11XM V5.6 (and later), NU is coded to use the UB.SYS pseudo handler for UNIBUS systems with greater than 256K bytes. The NC/NQ/NU handlers perform all interrupt processing at IRQ level (FORK level is never entered) and do not internally support device timeout. The EQ/EU device handlers are logically equivalent to the NQ/NU device handlers but were designed with special functions 206 (enable/disable frame bufferring), 207 (get physical ad- dress), 210 (get handler status block), 211 (abort job i/o, for SJ monitors only), and 212 (device time-out and reset). The EQ/EU handlers perform all interrupt processing at FORK level and donot internally support device timeout. These handlers may be conditionally assembled to support the RT11 SJ, SB, FB, and XM monitors (versions 5.3 and later) not supported by the NQ/NU device handlers. ETHERNET DEVICE HANDLERS Page 6-2 The EQ and EU handlers may be conditionally assembled for Version 6 of the TSX-Plus operating system. The 22-bit EU handler requires a change in the TSX sysgen file TSGEN.MAC to allocate 4 UMR registers to the EU handler. TSX-Plus versions 6.0 through 6.2 require a unique version of the EQ/EU handler with special functions 300 (get PLAS region size), 301 (initial- ize handler with PLAS region base address), and the support pro- gram ENPLAS.SAV. The program ENPLAS.SAV creates the PLAS memory region required by the handler. ETHERNET DEVICE HANDLERS Page 6-3 6.1 DEVICE HANDLER SYSTEM SUMMARY Summary of prebuilt EQ/EU/NC/NQ/NU device drivers and supported systems: RT-11 VERSION [5.3] [5.4] [5.5] [5.6 ...] TSX ----- ----- ----- --------- --- eqsjms.[ext] SJ/FB SJ/FB SJ/FB - - eusjms.[ext] SJ/FB SJ/FB SJ/FB - - eqsjps.[ext] SJ/FB SJ/FB SJ/FB - - eusjps.[ext] SJ/FB SJ/FB SJ/FB - - eqsbms.[ext] - - - SB/FB - eusbms.[ext] - - - SB/FB - eqsbps.[ext] - - - SB/FB - eusbps.[ext] - - - SB/FB - eq18xm.[ext] XM XM XM XB/XM/ZB/ZM - eq22xm.[ext] XM XM XM XB/XM/ZB/ZM - eu18xm.[ext] XM XM XM XB/XM/ZB/ZM - ncxv56.[ext] - ? ? XB/XM/ZB/ZM - nqxv56.[ext] - ? ? XB/XM/ZB/ZM - nuxv56.[ext] - ? ? XB/XM/ZB/ZM - eq18.v62 - - - - <= V6.2 eq22.v62 - - - - <= V6.2 eu18.v62 - - - - <= V6.2 eu22.v62 - - - - <= V6.2 eq18.tsx - - - - >= V6.4 eq22.tsx - - - - >= V6.4 eu18.tsx - - - - >= V6.4 eu22.tsx - - - - >= V6.4 ______.[ext] ext == sys, for monitor with device timeout ext == nys, for monitor without device timeout ____ms.[ext] Drivers are for LSI/11 processors not having a processor status word (PSW == @#177776). ____ps.[ext] Drivers are for all processors with a processor status word (PSW == @#177776). __sj__.[ext] Drivers contain special function 211 (abort job i/o) for RT11SJ monitors. ETHERNET DEVICE HANDLERS PAGE 6-4 DEVICE HANDLER SYSTEM SUMMARY 6.2 DEVICE HANDLER FEATURE SUMMARY Summary of prebuilt EQ/EU/NC/NQ/NU device driver features: SPFUNS DEVICE 206 207 210 211 212 EIS PSW UMR --- --- --- --- --- --- --- --- eqsjms.[ext] X - - X X - - - eusjms.[ext] X - - X X - - - eqsjps.[ext] X - - X X - X - eusjps.[ext] X - - X X - X - eqsbms.[ext] X - - - X - - - eusbms.[ext] X - - - X - - - eqsbps.[ext] X - - - X - X - eusbps.[ext] X - - - X - X - eq18xm.[ext] X X X - X X X - eq22xm.[ext] X X X - X X X - eu18xm.[ext] X X X - X X X - ncxv56.[ext] X X X - X X X - nqxv56.[ext] X X X - X X X - nuxv56.[ext] X X X - X X X X eq18.v62 X X X - X X X - eq22.v62 X X X - X X X - eu18.v62 X X X - X X X - eu22.v62 X X X - X X X X eq18.tsx X X X - X X X - eq22.tsx X X X - X X X - eu18.tsx X X X - X X X - eu22.tsx X X X - X X X X ______.[ext] ext == sys, for monitor with device timeout ext == nys, for monitor without device timeout ____ms.[ext] Drivers are for LSI/11 processors not having a processor status word (PSW == @#177776). ____ps.[ext] Drivers are for all processors with a processor status word (PSW == @#177776). __sj__.[ext] Drivers contain special function 211 (abort job i/o) for RT11SJ monitors. ETHERNET DEVICE HANDLERS PAGE 6-5 DEVICE HANDLER FEATURE SUMMARY 6.3 ALTERNATE DEUNA DEVICE HANDLERS In addition to the device handlers listed in the Device Handler tables above are 8 alternate handlers which may be re- quired when configuring a system using the DEUNA network inter- face. The DEUNA has very little internal buffer space for packets and requires more external buffers to operate reliably on networks with more than a few active computers. Testing on a PDP-11/44 / DEUNA system attached to a local network having over 250 active computers required 4 internal packet buffers for reliable operation. The additional EU handlers for SJFB and SBFB monitors listed in the following table have 4 internal packet buffers instead of the nominal 2 packet buffers. Summary of prebuilt 4 buffer EU device drivers: RT-11 VERSION [5.3] [5.4] [5.5] [5.6 ...] ----- ----- ----- --------- eusjm4.[ext] SJ/FB SJ/FB SJ/FB - eusjp4.[ext] SJ/FB SJ/FB SJ/FB - eusbm4.[ext] - - - SB/FB eusbp4.[ext] - - - SB/FB SPFUNS DEVICE 206 207 210 211 212 EIS PSW UMR --- --- --- --- --- --- --- --- eusjm4.[ext] X - - X X - - - eusjp4.[ext] X - - X X - X - eusbm4.[ext] X - - - X - - - eusbp4.[ext] X - - - X - X - ______.[ext] ext == sys, for monitor with device timeout ext == nys, for monitor without device timeout ____m4.[ext] Drivers are for LSI/11 processors not having a processor status word (PSW == @#177776). ____p4.[ext] Drivers are for all processors with a processor status word (PSW == @#177776). __sj__.[ext] Drivers contain special function 211 (abort job i/o) for RT11SJ monitors. ETHERNET DEVICE HANDLERS PAGE 6-6 ALTERNATE DEUNA DEVICE HANDLERS 6.4 PROGRAMMING Programs that call the Ethernet handler must follow a certain order. Write such programs with the following elements in the order indicated. 1. Use the .LOOKUP programmed request to open a channel to the device unit. 2. Allocate the unit using SPFUN 200. 3. Perform the Ethernet operation(s). 4. Deallocate the unit using SPFUN 200. 5. Use the .CLOSE programmed request to close the channel to the specified device unit. NOTE Special functions 207 (get physical address), 210 (get handler status block), 211 (abort job i/o), and 212 (device timeout / reset) do not require device alloca- tion. 6.5 USE OF SPECIAL FUNCTIONS (.SPFUN) The EQ/EU/NC/NQ/NU Ethernet handlers operate the Ethernet controllers using the .SPFUN programmed request with the follow- ing function codes: ETHERNET DEVICE HANDLERS PAGE 6-7 USE OF SPECIAL FUNCTIONS (.SPFUN) Function Code -------- ---- Allocate unit 200 Deallocate unit 200 Enable Promiscuous Mode 201 Disable Promiscuous Mode 201 Enable protocol type 202 Disable protocol type 202 Enable multicast address 203 Disable multicast address 203 Transmit Ethernet frame 204 Receive Ethernet frame 205 Enable frame bufferring 206 Disable frame bufferring 206 Get physical address 207 Get handler status block 210 Abort Job I/O 211 Receive Timeout / Reset 212 Transmit Timeout / Reset 212 Successful completion of a .SPFUN request clears the carry bit. Completion with an error sets the carry bit, and the status word in the buffer contains an error code. 6.5.1 Unit Specification (.SPFUN 200) The allocate unit special function allocates a unit for a job's exclusive use. The deallocate unit special function deallocates a unit so it can be used by another job. ETHERNET DEVICE HANDLERS PAGE 6-8 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.1.1 Allocate Unit - The following is the form of the special function allocate unit (.SPFUN 200): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 200 buf is the address of a 4-word buffer containing the status word and space for the station's physical address. The buffer contents are returned by the allocate unit special function. The high byte of the status word contains a 0. Allocate unit returns one of the following octal status codes in the low byte of the status word: 0 Success 2 Controller error while attempting to initialize the network interface 3 No resources (unit in use) 11 Reserved wcnt is 0 blkn is 1 crtn is the entry point of a completion routine ETHERNET DEVICE HANDLERS PAGE 6-9 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.1.2 Deallocate Unit - The following is the form of the special function deallocate unit (.SPFUN 200): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 200 buf is the address of a 1-word buffer containing the status word. The high byte of the status word contains a 0. Deallocate unit returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issueing the request. 2 Controller error while attempting to initialize the network interface 11 Unit still active wcnt is 0 blkn is 0 crtn is the entry point of a completion routine ETHERNET DEVICE HANDLERS PAGE 6-10 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.2 Promiscuous Mode (.SPFUN 201) The enable promiscuous mode special function enables the Ethernet hardware to receive all network traffic regardless of address or protocol. Any read request to the handler will re- turn the first available packet received by the controller in- terface. The disable promiscuous mode special function enables the ad- dress/protocol filtering provided by the Ethernet hardware and enables the specified protocol. 6.5.2.1 Enable Promiscuous Mode - The following is the form of the special function enable promiscuous mode (.SPFUN 201): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 201 buf is the address of a 1-word buffer containing the status word. The high byte of the status word contains a 0. Enable promiscuous mode returns one of the following octal status codes in the low byte of the status word: 0 Success 6 address/protocol active wcnt is 0 blkn is 1 crtn is the entry point of a completion routine ETHERNET DEVICE HANDLERS PAGE 6-11 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.2.2 Disable Promiscuous Mode - The following is the form of the special function disable promiscuous mode (which performs an enable protocol type) (.SPFUN 201): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 201 buf is the address of a 2-word buffer that contains the status word, followed by the 1-word protocol type that is to be enabled when the promiscuous mode is disabled. The high byte of the status word contains a 0. The disable promiscuous mode returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issueing the request. 2 Controller error while attempting to initialize the network interface 3 Reserved 6 Reserved 10 Protocol type in use wcnt is 0 blkn is 0 crtn is the entry point of a completion routine ETHERNET DEVICE HANDLERS PAGE 6-12 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.3 Protocol Type (.SPFUN 202) The enable protocol type special function adds a protocol type to those to be recognized by the Ethernet controller. Only one protocol type can be specified for each unit. At least one protocol type must be enabled to receive Ethernet frames. The disable protocol type special function removes the pro- tocol type from the list of those recognized by the Ethernet controller. 6.5.3.1 Enable Protocol Type - The following is the form of the special function enable pro- tocol type (.SPFUN 202): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 202 buf is the address of a 2-word buffer that contains the status word followed by the protocol type word. The high byte of the status word contains a 0. Enable protocol type returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issuing the request 2 Controller error while attempting to initialize the network interface 3 No resources (unit's protocol table full) 6 Reserved ETHERNET DEVICE HANDLERS PAGE 6-13 USE OF SPECIAL FUNCTIONS (.SPFUN) 10 Protocol type in use The protocol type is specified by the user wcnt is 0 blkn is 1 crtn is the entry point of a completion routine 6.5.3.2 Disable Protocol Type - The following is the form of the special function disable protocol type (.SPFUN 202): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 202 buf is the address of a 2-word buffer that contains the status word followed by the protocol type word. The high byte of the status word contains a 0. Disable protocol type returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issuing the request 2 Controller error while attempting to initialize the network interface If the disabled protocol type is not the same as the enabled protocol type for this unit then 'success' is returned. wcnt is 0 ETHERNET DEVICE HANDLERS PAGE 6-14 USE OF SPECIAL FUNCTIONS (.SPFUN) blkn is 0 crtn is the entry point of a completion routine 6.5.4 Multicast Address (.SPFUN 203) The enable multicast address special function adds the multi- cast address to those recognized by the Ethernet controller. Ypu need not specify the unit's physical or broadcast address. Only one multicast address is allowed per handler unit. The disable multicast address special function removes the multicast address from those to be recognized by the Ethernet controller. 6.5.4.1 Enable Multicast Address - The following is the form of the special function enable mul- ticast address (.SPFUN 203): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 203 buf is the address of a 4-word buffer that contains the status word, followed by the 3-word multicast address. The low order bit of the first address word should be a 1. The high byte of the status word contains a 0. Enable multicast address returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issueing the request. 2 Controller error while attempting to ETHERNET DEVICE HANDLERS PAGE 6-15 USE OF SPECIAL FUNCTIONS (.SPFUN) initialize the network interface 3 No resources (unit's address table is full, or hardware address table full) wcnt is 0 blkn is 1 crtn is the entry point of a completion routine 6.5.4.2 Disable Multicast Address - The following is the form of the special function disable multicast address (.SPFUN 203): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 203 buf is the address of a 4-word buffer that contains the status word, followed by the 3-word multicast address. The low order bit of the first address word should be a 1. The high byte of the status word contains a 0. Disable multicast address returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issueing the request. 2 Controller error while attempting to initialize the network interface If the disabled multicast address is not the same as the enabled multicast address for this unit then 'success' is returned. ETHERNET DEVICE HANDLERS PAGE 6-16 USE OF SPECIAL FUNCTIONS (.SPFUN) wcnt is 0 blkn is 0 crtn is the entry point of a completion routine 6.5.5 Transmit Ethernet Frame (.SPFUN 204) The special function transmit Ethernet frame transmits the Ethernet frame pointed to in the buf argument. If the source field of the frame is not zero, it is kept and used. If the source field of the frame is zero, the controllers physical ad- dress is inserted in the source field before transmission. The following is the form of the special function transmit Ethernet frame (.SPFUN 204): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 204 buf is the address of a variable size buffer containing the status word, followed by the Ethernet packet to be transmitted. The first word following the status word is reserved. Next is the 3-word destination address field followed by the 3-word source address field. The next word is the packet protocol type. Following this is the variable length packet containing from 23 to 750 words. The transmit Ethernet frame returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issueing the request. 2 Controller error while attempting to ETHERNET DEVICE HANDLERS PAGE 6-17 USE OF SPECIAL FUNCTIONS (.SPFUN) initialize the network interface 13 Transmit failed When status code 13 is returned in the low byte of the status word, transmit Ethernet frame returns one of the following octal status codes in the high byte of the status word: 1 Invalid frame length 2 Excessive collisions 3 Carrier check failed wcnt is determined by the variable size of the user buffer (including the status word and reserved word). The packet size (including the status word and reserved word) can vary between 32 and 759 words. blkn is 0 crtn is the entry point of a completion routine 6.5.6 Receive Ethernet Frame (.SPFUN 205) The receive Ethernet frame special function returns the next Ethernet packet with the desired unit address and protocol type to the buffer. The function does not return Ethernet frames that are received with errors. The following is the form of the special function receive Ethernet frame (.SPFUN 205): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 205 buf is the address of a variable size buffer containing the status word, a word containing the frame size, and followed by ETHERNET DEVICE HANDLERS PAGE 6-18 USE OF SPECIAL FUNCTIONS (.SPFUN) upto 757 words to receive the Ethernet frame. The buffer contents are returned by the receive Ethernet frame function. The high byte of the status word contains a 0. The receive Ethernet frame special function returns one of the following octal status codes in the low byte of the status word: 0 Success 1 Unknown unit. The specified unit was not opened by the job issueing the request. 2 Controller error while attempting to initialize the network interface wcnt is the size of the user buffer including the status and frame size words blkn is 0 crtn is the entry point of a completion routine 6.5.7 Frame Queueing (.SPFUN 206) The Enable frame queueing special function allows the handlers to internally queue received packets that match any enabled address/protocol even though a receive request has not been issued for that address/protocol or a previous packet has not been processed. The EQ handler normally allocates space for internally queueing upto 20 packets (this may be changed by mod- ifying 'rbcnt' in EQ.MAC and rebuilding the EQ handler). The 22-bit EU handler normally allocates space for internally queue- ing 10 packets and the 18-bit EU handler allocates space for 2 packets (this may be changed by modifying 'rbcnt' in EU.MAC and rebuilding the EU handlers). The disable frame queueing special function disables the in- ternal queueing of packets. This function may only be issued if all address/protocol pairs have been disabled. ETHERNET DEVICE HANDLERS PAGE 6-19 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.7.1 Enable Frame Queueing - The following is the form of the special function enable frame queueing (.SPFUN 206): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 206 buf is the address of a 1-word buffer for the returned status word which is always 0 wcnt is 0 blkn is 1 crtn is the entry point of a completion routine 6.5.7.2 Disable Frame Queueing - The following is the form of the special function disable frame queueing (.SPFUN 206): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 206 buf is the address of a 1-word buffer containing the status word. The high byte of the status word contains a 0. Disable frame queueing returns one of the following octal status codes in the low byte of the status word: ETHERNET DEVICE HANDLERS PAGE 6-20 USE OF SPECIAL FUNCTIONS (.SPFUN) 0 Success 6 address/protocol active wcnt is 0 blkn is 0 crtn is the entry point of a completion routine 6.5.8 Get Ethernet Address (.SPFUN 207) The get Ethernet address special function returns the physi- cal address of the Ethernet controller card. The following is the form of the special function get Ethernet address (.SPFUN 207): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 207 buf is the address of a 4-word buffer in which the status word, which is always 0, and the six byte physical Ethernet address are returned. wcnt is 0 blkn is 0 crtn is the entry point of a completion routine ETHERNET DEVICE HANDLERS PAGE 6-21 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.9 Get Ethernet Status Block (.SPFUN 210) The get Ethernet status block special function returns the handler's internal parameter block. The information contained in the parameter block includes the number of packets received and transmitted for each EQ/EU unit as well as timeout informa- tion. The following is the form of the special function get Ethernet status block (.SPFUN 210): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 210 buf is the address of a buffer into which wcnt words are written from the EQ/EU handlers status block. wcnt is the number of words to return to the buffer. The status word must be included in the word count. blkn is 0 crtn is the entry point of a completion routine The complete list of parameters in the status block may be found in the EQ/EU Ethernet handler files EQ.MAC, EU.MAC, and EI.MAC. The first word is always a status word of value 0, the following 4-byte (long integer) parameters are: eiipkt total receiver interrupts eiopkt total transmitter interrupts eirtmo total receive timeouts eixtmo total transmit timeouts eirun[8] received packets for each unit eixun[8] transmitted packets for each unit These are the only parameters used by any program in the 'TCP/IP Package for TSX-Plus' or 'TCP/IP Package for RT-11'. ETHERNET DEVICE HANDLERS PAGE 6-22 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.10 Abort Job I/O (.SPFUN 211) The abort job i/o special function is conditionally assembled into drivers for the RT11SJ monitors. The SJ monitor never calls the abort entry point in the device handler (either from a .ABTIO request or at job termination) this means that the inter- nally queued i/o requests will never complete and the monitor will lock waiting for the i/o to complete. This special func- tion calls the abort entry point clearing all internally queued elements associated with the current job. The following is the form of the special function Abort Job I/O (.SPFUN 211): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 211 buf is not used wcnt is not used blkn is not used crtn is the entry point of a completion routine 6.5.11 Timeout / Reset (.SPFUN 212) The functionality of the timeout / reset special function is equivalent to an internal device timeout. This implemenatation allows the handlers to be assembled for use with monitors with or without device timeout functionality. A user call to spfun 212 aborts any pending transmit packet, the network handler to be cleared, and the network device to be restarted. The actual device timeout interval is determined by the user program. ETHERNET DEVICE HANDLERS PAGE 6-23 USE OF SPECIAL FUNCTIONS (.SPFUN) 6.5.11.1 Receive Timeout / Reset - The receive timeout / reset (blkn = 0) causes the receive timeout counter to be incremeneted. The following is the form of the special function Receive Timeout / Reset (.SPFUN 212): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 212 buf is not used wcnt is not used blkn 0 crtn is the entry point of a completion routine 6.5.11.2 Transmit Timeout / Reset - The transmit timeout / reset (blkn = 1) causes the transmit timeout counter to be incremeneted. The following is the form of the special function Transmit Timeout / Reset (.SPFUN 212): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 212 buf is not used wcnt is not used ETHERNET DEVICE HANDLERS PAGE 6-24 USE OF SPECIAL FUNCTIONS (.SPFUN) blkn 1 crtn is the entry point of a completion routine 6.6 HANDLERS FOR TSX-PLUS V6.0 THROUGH V6.2 The EQ and EU Ethernet handlers configured for TSX-Plus ver- sions 6.0 through 6.2 have these additional .SPFUN programmed requests: Function Code -------- ---- Get PLAS Allocation Size 300 Initialize Handler 301 Successful completion of a .SPFUN request clears the carry bit. Completion with an error sets the carry bit without any error code. 6.6.1 Get PLAS Allocation Size (.SPFUN 300) The following is the form of the special function Get PLAS Alocation Size (.SPFUN 300): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 300 buf handler returns the requested allocation size, in 32. word increments, in the first word of the buffer wcnt is not used blkn is not used crtn is the entry point of a completion routine ETHERNET DEVICE HANDLERS PAGE 6-25 HANDLERS FOR TSX-PLUS V6.0 THROUGH V6.2 6.6.2 Initialize Handler (.SPFUN 301) The following is the form of the special function Initialize Handler (.SPFUN 301): Macro Call: .SPFUN area,chan,func,buf,wcnt,blkn,[crtn] where: area is address of 6-word EMT argument block chan is a channel number in the range 0 to 376 (octal) func is 301 buf the address of buf is the PLAS base address wcnt is not used blkn is not used crtn is the entry point of a completion routine Attempting to reinitialize the handler or to initialize the handler with a PLAS base address of 0 will be reported as an er- ror by setting the carry bit. 6.6.3 ENPLAS.SAV - Allocating the PLAS Region The program ENPLAS.SAV is a support program which creates the PLAS buffer required by the TSX-Plus V6.0 through V6.2 EQ and EU device handlers. The program uses .spfun 300 to get the buffer size, creates the PLAS region, uses .spfun 301 to handoff the PLAS region's Base Address to the device handler and to initial- ize the handler. This program must run before the EQ or EU device handler can be used. The device EN0: must be assigned before running ENPLAS.SAV. ASSIGN EU0: EN0: or ASSIGN EQ0: EN0: R ENPLAS.SAV ETHERNET DEVICE HANDLERS PAGE 6-26 HANDLERS FOR TSX-PLUS V6.0 THROUGH V6.2 The device handler requires only a single initialization to be used by the TCPIP.SAV server or the small system client programs. CHAPTER 7 BUILDING THE TCP/IP PACKAGE 7.1 C COMPILER The DECUS C Compiler and Assembler and the RT-11 Macro Assem- bler and Linker are required to build the the TCP/IP Package for RT-11 from the source files included in the distribution. The DECUS C Compiler is from the DECUS 11-SP-18 distribution with bug fixes made to the compiler and the library. (The updates are on logical disk CCDSK2.DSK). EIS and non-EIS versions of the compiler along with the assembler, library, and the necesary header files are included with the distribution to allow the package to be recompiled. 1. Create CDISK.DSK[1500] as C:, a logical disk for the C compiler 2. Copy the contents of the logical disk CCDSK1.DSK to C:. The device containing the compiler, assembler and header files should be assigned as device C:. The build procedures assume that the compiler and header files are on the logical device 'C:'. 3. Copy the compiler helper files from logical disk CCXDSK.DSK to C:. 4. Use the command file C:CCSET.EIS to copy the EIS specific files into the C: directory with the appropriate .SAV and .OBJ file types. 5. UCL CC and ASM commands. 1. For RT-11-XM V5.3 use file C:CCXASM.V53 to create the UCL commands to invoke CC and ASM. 2. For RT-11-XM V5.6 (and later) use file C:CCXASM.V56 to create the UCL commands to invoke CC and ASM. BUILDING THE TCP/IP PACKAGE PAGE 7-2 TCP/IP PACKAGE 7.2 TCP/IP PACKAGE The TCP/IP Package is supplied with the complete source code as an assemblage of C files (*.c), macro files (*.mac), header files (*.h), and an assortment of command files (*.com). 1. Copy the logical disks SRDSK1.DSK, SRDSK2.DSK, SRDSK3.DSK, and SRDSK4.DSK to a disk or logical disk having at least 10000 blocks of free space. 2. Use the command file BLDRT.SET to create the RT-11 con- ditional files. 3. The command file BLDALL.COM will compile and link the complete TCP/IP Package. Inspect BLDALL.COM to see how each individual component is built. An unloaded 11/73 processor will take from 40 to 50 minutes to compile and link the complete package. 4. Rename all .SAV files to .SXV files. 5. The command file RTV53.INS or RTV56.INS may be used to copy all the files necessary to configure a complete implementation of the TCP/IP Package for RT-11 to the TCP: directory. (This includes all the files found on logical disks RTDSK1.DSK, RTDSK2.DSK, and RTDSK3.DSK). 7.3 COMPILING OPTIONS The TCP/IP Package components may be compiled with or without the diagnostic options (the default is no diagnostics). Each component has an individual header file, e.g. VTCPIP.H for TCPIP.SAV, which contains define statements that have been com- mented out to exclude the diagnostics. Several other programs have optional sections that may be disabled by commenting out selected define statements. CHAPTER 8 DISTRIBUTION DISKS The "TCP/IP Package for TSX-Plus", the "TCP/IP Package for RT-11", and the "FTP and Telnet Package for Small Systems" are distributed as a combined package of 24 RX02 logical floppy disks: 1. TSDSK1 TCP/IP Package for TSX-Plus 2. TSDSK2 Executables for TSX-Plus Systems. 3. TSDSK3 (EQ/EU Device Driver Required) 4. RTDSK1 TCP/IP Package for RT-11 5. RTDSK2 Executables for RT-11 Mapped Systems. 6. RTDSK3 (EQ/EU/NC/NQ/NU Device Driver Required) 7. SRDSK1 TCP/IP Package Sources 8. SRDSK2 All source code files for: 9. SRDSK3 TCP/IP Package for TSX-Plus 10. SRDSK4 TCP/IP Package for RT-11 11. SMLTCP Small System Package Executables (EQ/EU/NC/NQ/NU Device Driver Required) 12. SSDSK1 Small System Package Sources 13. DVDSK1 EQ/EU Device Drivers 14. DVDSK2 NC/NQ/NU Device Drivers 15. CCDSK1 DECUS C Compiler, Assembler, and Libraries. 16. CCDSK2 DECUS C Source Changes 17. CCXDSK Compiler helper files for mapped RT-11 systems. 18. RTDOC SS and RT Package Documentation 19. TSXDOC TSX Package Documentation 20. RNODSK Package Documentation in RNO Format DISTRIBUTION DISKS Page 8-2 21. RTHTML RT-11 Docs in HTML Format 22. TSHTML TSX-Plus Docs in HTML Format 23. SSHTML Small System Docs in HTML Format 24. TCPIPM Minimal Distribution APPENDIX A HIDDEN OPTIONS A.1 DISABLE PASSWORD The -b option will disable the user/password query in pro- grams TELNET, RTELNT, FTP, RFTP, CNCT, RCNCT, MAIL, and MMAIL. Local users normally are not required to use passwords when ac- tivating TELNET, FTP, or CNCT. The MAIL and MMAIL programs and the network server programs RTELNT, RFTP, and RCNCT should not specify the -b option for security reasons. APPENDIX B TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG Page B-2 B.1 VERSION 2.40 V02.40 15-Jun-2008 PORTIN.C Updated makesocket() socket scanning to start socket closing on orphaned sockets after suitable timeout periods. CLIUTL.C Fixed code in listen() which would cause an inifinite loop if the socket state change to SLISTEN was not detected. Added error checking for listen() startup failure. RHTTP.C, RPOP3.C, RAUTH.C, RGOPH.C, RSMTP.C, RLPD.C RCNCT.C, RPCNCT.C, RFTP.C, RTLNTA.C, and RPTLNA.C Scan for end of line and terminate line fixed for possible line buffer overflow. Added error checking for listen() startup failure and to detect socket corruption. FTPB.C, FTPL.C, and PMON.C Added error checking for listen() startup failure. TELNET.C and CNCT.C Updated various common constructs of the type a->b located throughout the programs to use a common value. Removed program wide global values from function argument lists. JOBMON.MAC Corrected the system call to the TSX 'job status' emt. EQ.MAC Updated the EQ device driver interrupt processing to be more consistant with the EU device driver. DFAULT.H, LCLSKT.C, GBLSKT.C, and SKTSKT.C Reduced maximum number of TCPIP 'sockets' to 16. TSX-Plus Observations: When configuring the NGR parameter in TSGEN.MAC (The total number of 'shared' global regions used by all jobs) the minimum value must be set to the sum of the number of time share lines plus the total number of subprocess windows plus the number of TCPIP sockets plus one. This is required even though the subprocess windows are not shared. When configuring the TBLDEF parameters in TSGEN.MAC, e.g. with TBLDEF 2.,8.,10.,1. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-3 VERSION 2.40 a value of 2 + 8 + 16 + 1 is the minimum value required for NGR. It has been observed that if the detached jobs parameter is increased much beyond 10. TSX becomes unstable with heavy network access and will consistently freeze. This effect is quite repeatable and may change with different system configurations. (TSX-Plus V6.5) TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-4 VERSION 2.40 B.2 VERSION 2.39 V02.39 15-Jan-2008 RFTP.C Because the SIZE command always reports file sizes as multiples of 512 bytes, transfers of ASCII files may become problematic if the FTP client compares the transferred file size to the SIZE command file size as they are in general NOT the same. Thus the default has been changed to report the SIZE command as NOT implemented. The -f option has been added to enable the SIZE command if required. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-5 VERSION 2.39 B.3 VERSION 2.38 V02.38 26-Mar-2007 MAILER.C Increased the maximum line length from 128 to 512 characters. Various header lines were exceeding 180 characters causeing malformed headers when truncated to 128 characters. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-6 VERSION 2.38 B.4 VERSION 2.37 V02.37 1-Feb-2007 RFTP.C Updated RFTP.C for RT-11 to not specify any files as logical disks. The RT-11 version does not support the change directory (cd) command into logical disk files. TSXUTL.C Fixed the change directory (cd) string parsing to ignore superfluous NULL subdirectorys, e.g.: cd dm5://xdsk.dsk/, cd dl3://, ... PASWRD.C Corrected the 'Access Directory' selection processing and display code. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-7 VERSION 2.37 B.5 VERSION 2.36 V02.36 15-Nov-2006 MAILER.C Corrected mailer scan and forwarding routines. MAILA.C, MAILB.C, and MMAIL.C Added code to 'complete' an email address when only a local username is given. B.6 VERSION 2.35 V02.35 1-Oct-2006 MAILA.C, MAILB.C, MMAIL.C, MAILER, and RSMTP.C Corrected mail 'index' file processing which synchronizes the receiving and sending of mail messages. MAILER.C and PASWRD.C Added mail forwarding for local users. A user's mail may be forwarded to another local user account or to a remote computer. The MAILER service should now be activated by MAIL, MMAIL, RSMTP, and RPOP3. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-8 VERSION 2.35 B.7 VERSION 2.34 V02.34 1-Jan-2006 RFTP.C The command filespecs are now scanned to remove badly formed file paths created by browsers which assume only heirarchical file structures. RTLNTA.C, RTLNTB.C, RCNCT.C, RFTP.C, RHTTP.C, RLPD, RSMTP.C, RPOP3.C, RGOPH.C, and RAUTH.C The TCP/IP server programs have been updated to allow an alternate service port to be specified TSX-Plus Only:. The TCPIP.CFG file must specify a unique server command file for the alternate port option. e.g.: service=33,1,TCP:rtelnt.s33 # alternate port rtelnt.s33: ... run/single TCP:rtelnt -actlqpyz 0 2 1 33 PAS:paswrd.fil 15 600 RPTLNA.C, RPTLNB.C, RPCNCT.C, TELNET.C, CNCT.C, FTPA.C, MAILA.C, and PMON.C Various changes/corrections in help text, no changes in program code. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-9 VERSION 2.34 B.8 VERSION 2.33 V02.33 15-Jan-2004 EI.MAC, EU.MAC, and EQ.MAC The network device drivers have been rewritten to remove the internal device time-out code. This change means that the RT-11 monitors no longer are required to have the sysgen device time-out option. The device time-out code is now implemented through a device handler special function (spfun 212). The spfun 212 is an optional device handler function. To utilize this device time-out option the user program must include coding to determine when a time-out has occurred and call spfun 212 to initialize the network interface. [ The removal of the device time-out code simplifies the handler. The device handler no longer requires the .timio, .ctimio, or .sync processing. This also means that the time-out configuration is completely user programmable. ] NIV56.MAC, NCV56.MAC, NQV56.MAC, and NUV56.MAC Added the special function spfun 212 to the DEC network device drivers. This function adds device time-out to the NC, NQ, and NU handlers. The functionality is identical to that described for the EQ and EU drivers above. ENDRVR.MAC and SYSTEM.MAC Updated ENDRVR.MAC to support the Network Device Time-Out special function spfun 212. If the transmission of a packet does not complete or return an error within 4 seconds then an xmit time-out call (spfun 212, block = 1) initializes the network interface. Similarly, if no packets are recieved within 1 minute then a recv time-out call (spfun 212, block = 0) initializes the network interface. The spfun 212 calls update the driver time-out counters if the ethernet status block option (spfun 210) is included. SYSTEM.MAC was updated to include extra queue elements for the two added .mrkt/.cmkt timing channels. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-10 VERSION 2.33 B.9 VERSION 2.32 V02.32 1-Apr-2003 TCP.C: Updated ackcheck(), estabcon(), checkfin(), and the routines calling these functions. The function ackcheck() notifies the client program via an event that data has been ACKed. Redundant CONCLOSE event removed from checkfin(). The function estabcon() notifies the client program with the CONDATA event and now does not ACK the recieved data. The ACK will be generated when the data has been DEQUEUEd by the client program. SERVER.C and SRVUTL.C: Moved checking for output data with outqpsh() to ntsleep() (from SERVER.C to SRVUTL.C). TCP.C, EVTDEF.H, and DFAULT.H: A long standing 'synchronization' problem between the TCPIP server and the client programs has been found. No event was being sent from the server program to the clients when the outgoing data had been accepted by the remote host. A new event has been added to the CONCLASS: CONSENT. This new event has been added to the event definitions in EVTDEF.H. The function ackcheck() in TCP.C has been updated for the synchronization and repeated ACK checks. This correction has allowed the removal of all 'transfer delay' timimg code in modules FTPA.C, FTPB.C, FTPL.C, RFTP.C, RHTTP.C, and RGOPH.C. SRVUTL.C, CLIUTL.H, and PRODEF.H: Added the code to allow the last packet transferred by transq() to be immediately retransmitted. This is the note in transq(): /* * This is really %#@&$*. * Most systems use a 'delayed ACK' when receiving * small packets. This may result in very low * transfer rates. Some systems will ACK on an * immediate duplicate. So here we send a duplicate * packet if enabled. */ This retransmit is only applicable to data packets not ACK packets or any other control packet. Updated the routines outqpsh() and outqoff(). TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-11 VERSION 2.32 FTPA.C, FTPB.C, FTPL.C, RFTP.C, RHTTP.C, and RGOPH.C: To significantly increase data transfer rates the fread(), fwrite(), and NULL removal routines have been replaced with MACRO routines. The function blkrd() reads multiple disk blocks directly into the read buffer. The function blkwt() writes data directly from the data buffer. The function blkstr() is a fast NULL removal routine replacing the previous 'for' loop. FTPA.C, FTPB.C, FTPPI.H, and FTPL.C: Added the command 'duplicate' to enable/disable the transmission of duplicate packets. RFTP.C, RHTTP.C, and RGOPH.C: Added the command line option '-w' to enable duplicate packet transmission. CLIUTL.C, FTPB.C, FTPL.C, and RFTP.C: Added code to copy the mseg, mwin, and mtu values from the 'control socket' to the 'data socket'. RFTP.C: Check for a repeated PORT command. Terminate connection on third identical PORT command. SCRNAC.C: Updated SKTMON Screen A to indicate if duplicate packet transmission is enabled/disabled. SCRNDI.C and SCRNPT.C: Updated display window to enumerate the individual TCP/IP flags. V_____.H: Restored the '#define DEBUGOPTION' in all the V_____.H header files. This allows individual programs to be compiled with debugging. The '#define DEBUGOPTION' in DFAULT.H remains to allow all programs to be compiled with debugging by changing just this one file. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-12 VERSION 2.32 B.10 VERSION 2.31 V02.31 1-Dec-2002 FTPL.C: Updated STOR and RETR functionality to include RT-11 Device Read and Write. (Required a change to the C I/O Library routine IOFOPA.MAC) Added check for file size specification before appending "[-1]" to write file specifications. TSXUTL.C: Added check for file size specification before appending "[-1]" to write file specifications. RTFILE.C: Various minor changes to rtparse(), rtwild(), and rtstring(). IOFOPA.MAC: Observations of RT-11 / TSX-Plus .csispc responses which in turn required a modification to the C-Library I/O routine to maintain compatability with all versions of RT-11 and TSX-Plus: Mode RT (V5.3) TSX-Plus ---- --------- -------- DY0: ok ok DY0:= error ok DY0:. ok ok DY0:.= error ok DY0:[-1] error ok DY0:[-1]= error ok DY0:A ok ok DY0:A= ok ok DY0:.E ok ok DY0:.E= error ok DY0:A. ok ok DY0:A.= ok ok DY0:A[-1] error ok DY0:A[-1]= ok ok DY0:A.[-1] error ok DY0:A.[-1]= ok ok DY0:.E[-1] error ok DY0:.E[-1]= error ok EU.MAC: Discovered that the difference between a DELUA and DEUNA network cards' interrupt response to running out of read-buffers would cause the DEUNA to enter an interrupt race condition in the handler. This problem would result in exceedingly slow transfers, TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-13 VERSION 2.31 a driver hang, or system crash. A minor driver change has corrected this problem. TCP/IP PACKAGE FOR TSX-PLUS / RT-11 CHANGE LOG PAGE B-14 VERSION 2.31 B.11 VERSION 2.30 V02.30 25-Oct-2002 Slow file transfer problems caused by TCPIP server packet processing routines not updating the transfer flag skt->out.lasttime properly. Files updated: SERVER.C, SRVUTL.C, TCP.C, and DFAULT.H Changed port number sequence to a pseudo random value based on the current clock ticks. File PROTIN.C modified. SUSPND.MAC suspend/resume code was modified. Server programs RFTP.C, RHTTP.C, and RGOPH.C updated. Client programs FTPB.C and FTPL.C updated. The RPTLNT.C file was split into RPTLNA.C and RPTLNB.C because of the C compiler complaints of 'OUT-OF-SPACE'. Moved the '#define DEBUGOPTION' to VRSION.H from all the V_____.H header files. 4-July-2002 Fixed a possible problem in RPOP3.C [topline()] which could cause file truncation if mail file exceeds 32767 lines.



Return to TCP/IP Documentation Index






...  Home Page


Last Updated: June 2008